Models > KUDW02FRBL4

KUDW02FRBL4 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDW02FRBL4

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDW02FRBL4, or you can search by name or part description. You can also find your part by where it is located on the KUDW02FRBL4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDW02FRBL4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$22.27

Door Balance Link Kit

This kit includes 2 door balance links and 2 door balance mounts with wheels.

$45.00

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

$8.07

Mounting Bracket

Sold individually.

$48.45

Silverware Basket - Gray

This is a basket for washing flatware or silverware in your dishwasher.

$20.38

Chopper Assembly

This chopper assembly chops/minces the food particles to prevent clogging of the dishwasher pump.

$21.38

Bi-Metal Fuse

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Also known as Thermal Fuse.

$15.27

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$15.66

Rinse Aid Cap

$3.96

Rubber Washer

Sold individually. Used with the heating element.

$137.62

Circulation Pump Motor with Impeller - 60Hz 120V

This part has a closed cast motor housing. The sump housing is sold separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 279 of 284 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 178 of 187 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to th... read more

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 91 of 99 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more