KUDU03STWH0 KitchenAid Dishwasher - Instructions

Real easy there was no guess work after watching your video on how to change the door balance kit. Having that video on the same page that I ordered the part was a great Idea. The guy that thought of that should get a Raise.

I followed the on line video instructions and the repair was completed with a hitch. The seal did not display the 'white stripe', but the enclosed illustration cleared up any question I had about proper insertion. The part arrived within 24 hrs of shipment! I will use Parts Select exclusively in the future! No more big bucks to have a Sears guy simply plug in a new part.

Repair was very easy...Thank goodness for the viedo...The part came the next day...I would recomend looping the link first...then attaching it to the spring.....

turned off h20 disconnect h20 and drain. pulled out dish washer took new part installed. Put back together in opposite order. then ran it to make sure I had no leaks. put cover back on and made kids do the dishes. really easy!

Excellent, Very easy to repair and the video showed me how to do-it-myself.Thank you

The hardest thing in installing the pump was pulling the dishwasher from under the counter. Once that was done and the mess with drain hoses and supply hoses was cleaned up, all it took was undoing one bolt to turn and remove the motor by turning in counter clockwise. the seal comes with the new motor and don't forget to reconnect the wire harness to the new motor on re-assembly.

1.opened the door removed the two anchoring screws at the top of the dishwasher. 2.slid out the machine, layed it on its side on a towel for water spill. 3.unplugged the old motor. 4. used 1/4 inch ratchet with 6 inch extension and 3/8 inch socket, removed the mounting bolt. 5. twisted the motor clockwise approx. 1/4 turn and removed the old motor with impeller. 7. repeated reverse method to install.

I ordered a repair kit and replaced the cord linkage without any tools other than those to pull the bottom panel and screws from the top retainer clips. Great instructions and extremely easy repair myself. Thank you.

Removed torx screws from rear of door. Openned door assembly and replaced board...very easy...about twenty minutes total. It's working fine and we're looking for years of additional service.

I cut the breaker and disconnected the in and out water lines, then removed the washer. Once on its side, I took it apart until I found what was broken. The chopper unit had broken and parts were sucked into the pump. After going online and finding/ordering all the parts, I cleaned everything and put it back together so as not to lose anything. When the parts came in,it was an easy job to replace the broken parts and have it back in use. The repair would have cost over $350 and my parts bill was less than $90. Thanks

I looked on your website under our model number. There I found various descriptions for the problem I had. Under the problem column, I found the possible parts needed. Turns out I needed new door pulleys and ropes. We watched the video provided by your site,pulled out the dishwasher, and changed out the ropes and wheel assemblys. Squeak is gone, door is balanced. Mission accomplished!

The hardest part was pulling the dishwasher out for the repair. I had to disconnect the water line to get the 2 feet required. Replacing the part took minutes. The springs were hard to extend in the limited space so I used pliers to pull them.

it was the motor bearing. ordered the whole pump assembley sunday night it came tuesday no bull one day 8 hours shipping. they have a video it shows you step by step it was cake but one day shipping and they didn`t even throw it over the fince.no laber cost $$$$$$$$ thank for the help.

I removed the two screws holding the dishwasher under the counter, and pulled out the unit about 10 inches, which allowed access to the door balance string and spring. After removing the old balance string I hooked the new one in and attached the spring. Then it was just an easy job to push the dishwasher back under the counter top and re-install the two screws. The replacement balance kit was not exactly the same as the OEM part, and rubbed on the guide wheels some, but it appears to work.

I just attached it to the top rack by using the other pivot clips as an example.