Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDS35FXSS2

KUDS35FXSS2 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDS35FXSS2

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDS35FXSS2, or you can search by name or part description. You can also find your part by where it is located on the KUDS35FXSS2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDS35FXSS2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$40.03

Rack Adjuster Kit - Left and Right Side

The rack adjuster connects to the dishrack and is used to change the height of the rack. This kit includes the parts to replace the left and right-side rack adjusters and has been ...

Order within the next 8 hrs and your part ships today!
$21.17

Wheel

The lower dishrack wheel is used in a dishwasher to easily roll rack back and forth on the rails. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. Slide the rack back in the washer to make sure it is installed correctly. Refer to the manual provided by the manufacturer for further instructions.

Order within the next 8 hrs and your part ships today!
$17.53

Door Balance Link Kit

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwashe...

Order within the next 8 hrs and your part ships today!
$6.30

Rack Stop Clip

This part goes on the end of the rail to stop the dishrack from falling out.

Order within the next 8 hrs and your part ships today!
$5.07

Tine Pivot

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. The clip is used to keep the tine row in place in the dishrack. ...

Order within the next 8 hrs and your part ships today!
$17.71

Chopper Assembly

This part chops up/mince the food particles to prevent from clogging the dishwasher pump.

Order within the next 8 hrs and your part ships today!
$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher f...

Order within the next 8 hrs and your part ships today!
$31.93

Positioner

Also known as rack adjuster. Sold individually.

Order within the next 8 hrs and your part ships today!
$26.28

Tine Row

The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your...

Order within the next 8 hrs and your part ships today!
$30.09

Drawer Track

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 521 of 535 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 283 of 312 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more

Loud grinding noise from water pump

  • Customer: Steve from Inver Grove Heights, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 176 of 190 people found this instruction helpful
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put th... read more