Models > KUDS30IXBL0 > Instructions

KUDS30IXBL0 KitchenAid Dishwasher - Instructions

All installation instructions for KUDS30IXBL0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDS30IXBL0
421-435 of 505
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher was not cleaning.

  • Customer: Scott from Seattle WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took out the roller trays, removed upper wash plumbing, and lower drain cover parts. I found out Scotchbrite clogged and damaged the screen and blade. R&R'ed both parts and now the dishwasher is like new again

Broken rollers on basket

  • Customer: Kent from Melbourne FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove and replace clips.

Door Link attached to the spring broke

  • Customer: Lou from Irvine CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the video it was real easy

The wheels on the upper rack had broken off

  • Customer: Holly from Palm Harbor FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The upper rack would not stay in place without the wheels. They had broken off. We use the sanitary cycle daily and I think we weakened the plastic wheels. I had a service man come who wanted $250 to fix the machine. I was able to look at a comparable machine in the store and figure out that it was snapped together and I could repair it myself. I unsnapped the wheel assembly and replaced it. The second side needed a little more "elbow grease" and my husband was able to unsnap that side and replace the wheel assembly.

Dish washer would notstart. No elect power

  • Customer: DANIEL from DOVER DE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
First turn off power to the dishwasher at the circuit breaker! Check the door panel screws they were star screws which I was able to remove with an allen wrench(more difficult). Follow the instruction included in the Fuse package. Follow and understand each step before doing the task and it will go smoothly.

WHeel had broken on upper rack slide out

  • Customer: Paul from Encinitas CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the tray out and set it on it's side. The rack adjuster just unsnap and snaps together real easily. I used the screwdriver to carefully pry apart the pieces where they snap together and that is all. Goes together real easy

Broken door balance link

  • Customer: John from Oxford OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled the dishwasher out to remove the broken link; attached the link to the spring; attached the spring to the frame; treaded the link around the lower part of the pulley; attached the link to the door; and treaded the link around the upper part of the pulley while pulling on the spring.

The top spinner fell off and would not snap back on

  • Customer: Thomas from Knoxville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Bought a replacement spinner which came with the litte round connector piece. The connector piece had worn down (the spinner probably got caught on a tall glass or pot). Anyway, for ease of access, you remove the bottom and top racks, unscrew two screws (one on the top and one on the back of the dishwasher that holds the water piping). Then pull the water piping assembly down from the top until you can remove the round connecting piece. The tip of mine was worn off which is why the spinner would not stay on. Once you replace the round connector piece, snap the spinner into it, put the screws back in and you are done. Very easy fix for about $22 including S&H.

Broken roller clip on rack adjuster

  • Customer: Mark from Ladera Ranch CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
You don't need any tools for this repair. Everything snaps apart and back together again. First, flip open the two blue end stops on the upper rack rails. Pull out upper rack, place on kitchen counter. Begin on the inside of the adjuster you're replacing (I had to do both). There are plastic clips at both ends of the adjuster that hold it tight to the rack. One is longer, one is shorter. Unclip the long one from the rack by pushing with your fingers. Then slide the clip until it is free. Slide the short clip up until it is free. Set both clips aside. There is one plastic clip remaining in the center of the adjuster. Remove it by squeezing and pushing the tangs that stick through the the rack into the adjuster. The adjuster is now free. Remove and replace adjuster with new part and reverse sequence to install. Note: if adjuster does not operate properly up-down (there should be a "click" at both positions), remove the adjuster and move the blue lever inside the plastic housing on the rack. Re-assemble and re-test for "clicks". It took me a few times, but I finally got it. Put the rack back in the dishwasher and flip close the blue end stops. Done!

Roller on adjuster on upper rack was broken

  • Customer: Michael from Lisle IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered replacement adjuster, removed the old one, and installed the new one. Just have to be sure to re-attach new one in the same place as the old one. Very simple repair.

Wheel came apart from top rack

  • Customer: Renee from Johnston IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was like a puzzle. I just looked at the other side of the rack. There are no screws;just plastic brackets. It would have been nice to have written directions but overall it went fairly smooth.

Door was noisy

  • Customer: Angela from Westfield IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions from the partselect video and replaced the damaged door balance part. I ended up having to adjust the plastic wheel piece because the new strings were shorter than the original but luckily there was another screw hole to accommodate the shorter strings. I did replace both sides. Overall, this was a very easy repair thanks to partselect and now my door works great. I will definitely be using this site in the future!

Roller on left rack adjuster broke

  • Customer: Dan from Vero Beach FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Used screw driver to remove brackets on the adjuster. installed new part by snapping back into place. Great customer service from PartSelect. Ordered part on Monday morning and received it after lunch next day.

wheels came off top rack

  • Customer: Edward from Gainesville VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Had some difficulty taking off the old platsic clips that secure the wheel assemly to the shelf because they are all snap-on/snap-in assemblies and could be broken easily. So extreme care as well as careful examination of what to do to what was required. I suggest that when you buy the wheel assembly you also buy the two clip-on/clip-in as well. That way you really don't have to worry if you break one or both and you could just "horse" them apart/off. Putting it back together is a "snap"........literally.

Prongs holding wheel to upper rack trolly assembly broken.

  • Customer: Alan from Webster Groves MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Printed the expolded diagram for the upper rack asembly when I ordered the part and retained to use as a reference for replacing the rack adjuster. Part arrived within three days or ordering. Used screwdriver to remove clips holding broken adjuster in place and referenced the diagram to attach the new adjuster to the rack. From start to finish was no more than 10 minutes.
All Instructions for the KUDS30IXBL0
421-435 of 505