KUDS30IXBL0 KitchenAid Dishwasher - Instructions

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

This is simple, we don't know exactly how, but when we used the dishwasher the cap must not have been twisted correctly, and after the dishwasher shut down we discovered the cap was on the heating coil and melted. I know that it was easy to fix, but the reason I ordered it from PartsSelect was their price was much lower than Kitchen Aids, (the maker), Lowes (where we bought it), and other sites we searched for the part.

1. Put a towel over the bottom of the machine. (In case you drop the screw... duh!)

2. Remove the top screw.

3. Replace the snap pin (pointy end DOWN.)

4. Snap the spinner in place.

5. Replace the screw. (Or go to the hardware store to replace the screw you dropped into the bottom of the dishwasher. Dashitall!)

Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.

First let me tell you I am not a "handyman". I am a 50 year old housewife who was determined not to shell out $$$ if I could help it. I researched on the internet what could be the problem...it was more than likely the chopper assembly. I found a youtube video that showed how to get to the chopper assembly. So I removed the racks by dislodging the end clips. Next I took the bottom tub sprayer off by holding the middle with my fingers and turning the blade counter clockwise. Next, I unscrewed the line that ran in the back and up to the top sprayer (I only removed the one screw so I could slide it to the right slightly so I could remove it from the connector at the bottom and it revealed four screws that needed to come out of the mesh cover. After removing that there is one more screw that comes out of the shroud that covers the chopper assembly. I cleaned the area removed the chopper assembly (totally gunked up) and replaced it with the new one I purchased here...(lightening fast shipping btw!!...Yea! for PartsSelect.com....you guys rock!) I checked for gunk in the rubber valve assembly, super easy to remove/replace. Vacuumed standing water with my shop vac to get any errant noodles and food bits and reassembled all of the housing and lines in reverse order. Before I ran my dishwasher I put some clean water in the bottom...just poured about 32 oz in. Whether you need to or not....I don't know but figured it wouldn't hurt. IT WORKED LIKE A CHAMP! Super clean dishes again!! I felt so empowered and the whole thing cost me less than 20 bucks! Listen ladies....and men....this is super easy....If I can do it....any one can!

My dishwasher motor was getting very noisy lately and finally died altogether. (the fwd bearing and seals had worn out. There was a small pile of what looked like white sand under the motor from the wear) I removed the dishwasher from the counter after turning off the power at the breaker box. I then turned the dishwasher on its side. The pump motor is removed by first removing the electrical connector, then loosening the retaining bolt and twisting the motor counterclockwise about a quarter turn. The gasket required a little force to become unseated from the housing but not to bad. Wiggle and pull! Be sure to take a look at the alignment at this point to facilitate reinstallation.To install the new motor, align the mark on the impeller(small delta) with the mark on the motor. Insert Motor into housing and turn clockwise one quarter turn till retaining bolt hole is aligned. Install retaining bolt. Be sure to note the position of the stainless steel screen where you insert the motor. Place it back in position before installing the pump if it is disturbed. I lubed the oring with vaseline prior to install also. The new oring was diffrent and did not feel very tight when i installed , but there were no leaks and the dishwasher is running like new. Partselect had the part at my door the next day with no upgrade in shipping charges and I will use them in the future. This forum helped me choose them and made the task easier to do. Hope this helps you as well.

After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!

First, I replaced the bottom door seal. You will need magnetic nut drivers because of the location of the 3/16 screws that hold the seal in place. you also need a 1/4 in nut driver to remove plastic cover that covers up the 5 3/16 screws. Last you need a small star driver to remove the door screws. Note 4 of the door screws, the 4 on top of the door are much longer than the side screws. With all this said, this seal was not my problem. I then replaced the large black rubber seal around the tub. Be sure if you do this you fold the seal in half and start in the middle of the top of the opening so you have the exact amount of seal left over on both sides. Also when you remove the old seal, clean the area it was removed from with a damp cloth. Turns out, That was not my problem either. So now I will move to the next step to see where the water is coming from but maybe this information will help someone with a simple door leak.

I took a picture of the old assemblies position. Then I removed one side. It was original and held in place by plastic snaps. We followed the instructions on the first side. The metal wheel assembly and the housing have matching channel & grove so the metal fits into the channel on the housing. We accidentally placed the metal wheel assembly in the adjustment housing backwards then could not get it out and broke two small plastic tabs getting it back out. Turns out that was not a fatal error. We had a bit of difficulty determining the exact positioning of the actuator in the housing and how the housing fit to the rack. One has to really look hard at the instructions. !!!A YouTube video would be very nice for this!!! Once we had the positioning then the assembly went together very easily. The two screws went in easily with a ratchet nut driver and star bit. (an adapter is provided for those who don't have the star bit). The second side was incredibly easy since I knew exactly how to put it together the second time. First side: 20-25 min. Second side 5 min.

Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

1. Disconnect power at the breaker, 2. remove two wood screws fastening the dishwasher to the cabinet and slide the unit out approximately 2 inches. 3. Remove old latch strike and replace with redesigned strike. 4. Slide unit in and reattached to cabinet. 5. Remove 11 screws holding inner panel of door assembly and one screw holding user interface unit to door. 6. Disconnect snap cable to latch assembly and replace the latch unit. 7. Reassemble.

Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.

To empty the water in the dishwater basin, I pushed the cancel button and closed the door. I then turned the electrical breaker to the off position that supplies electricity to the dishwasher. I confirmed the power was off by attempting to start the dishwaser. I removed the metal plate between the dishwater door and the floor by removing the two screws. I removed the two screws that connect the top of the dishwasher to the underside of the countertop. I shut the water valve that supplies hot water to the dishwasher (mine was located under the sink). I disconnected the drain hose (plastic) by using pliers to loosen the clamp the holds the hose on the outlet of the drain pump (drain pump is much smaller than the pump that needed replacement). A towell is handy to soak up the water that comes out the hoses. I loosened the nut on the water supply hose (this was difficult because of lack of room)using a wrench and pliers. I opened the door on the metal box that houses the wire nuts for the electrical connection to dishwater, and I removed the wire nuts and the screw for the ground wire. Once the white, black, and gound wires were disconnected, I could pull the dishwater out. I also had to pull the drain hose out from the clips on the side of the washer to pull the dishwasher out into the middle of the kitchen floor. I flipped the dishwasher on its back. I removed the single bolt that held the broken pump motor to the dishwasher, and then the motor twisted counterclockwise and I pulled it out. The pump shaft would not turn freely with my pliers, so I knew the motor was broken. I removed the pump end (impeller) from the dishwasher by tapping it with my screwdriver. The impeller end came out along with a metal screen. The metal screen was 50% plugged, so I cleaned it and put it back in place. I wet the gasket on the new pump motor and slid it back in place while rotating clockwise and locking it in place with the tabs. I replaced the bolt that holds the motor in place and reversed the repair procedure to re-install the dishwasher. Be sure to run the dishwasher and look for any leaks. The last step is to replace the metal plate between the floor and door. While I had the dishwasher pulled out, I discovered another problem with the pulleys and strings that prevent the heavy door from flopping down, but I won't include this repair. The pump and motor must have been failing for some time because the dishwasher is much quieter now and the dishwasher is much faster. I am sure the plugged screen didn't help either.

Simply snap the old one off and snap the new one on. Simple as that less than 15 seconds.