This rack adjuster kit (Dishrack Adjuster Kit, Adjuster Kit, Dishwasher Rack Adjuster) will adjust the height of the upper rack of your dishwasher. It connects to the dishrack. The kit is constructed...
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and fal...
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the ...
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack wil...
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
$67.53
In Stock
Questions And Answers for KUDS30FXSSA
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Diana
January 21, 2024
Where is the filter .? OR is this model self cleaning?
For model number KUDS30FXSSA
Hi Diana, thank you for your inquiry. The filter accumulator assembly, part number PS897295, is located at the bottom of the dishwasher under the lower spray arm. We have attached a relevant video which may not be of the exact model but will help you locate the accumulator. Based on our research, your model does not have a self-cleaning feature. We hope this information is useful!
Replacement was pretty easy after figuring out how to unsnap/unlock the old pieces. Tools only used to do a little prying and poking, but really aren't needed. Everything either snaps or slides together. Piece of cake
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
I took the broken basket adjuster off and then attached the new one. It wasn't too difficult, however some removal instructions and re-install instructions( or just a picture supplied) would have been helpful. This isn't an issue for a mechanically inclined person, but would be a challenge for someone that isn't. Thanks.