Models > KUDS03FTBT0

KUDS03FTBT0 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDS03FTBT0

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDS03FTBT0, or you can search by name or part description. You can also find your part by where it is located on the KUDS03FTBT0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDS03FTBT0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$22.27

Door Balance Link Kit

This kit includes 2 door balance links and 2 door balance mounts with wheels.

$45.00

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

$8.07

Mounting Bracket

Sold individually.

$48.45

Silverware Basket - Gray

This is a basket for washing flatware or silverware in your dishwasher.

$21.38

Bi-Metal Fuse

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit i...

$16.43

Rinse Aid Cap

This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.

$15.27

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$18.71

Chopper Assembly

This chopper assembly chops up/mince the food particles to prevent from clogging the dishwasher pump.

$3.96

Rubber Washer

Sold individually. Used with the heating element.

$137.62

Circulation Pump Motor with Impeller - 60Hz 120V

This part has a closed cast motor housing. The sump housing is sold separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 282 of 287 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 92 of 100 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more

Loud grinding noise from water pump

  • Customer: Steve from Inver Grove Heights MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 91 of 98 people found this instruction helpful
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put th... read more