KUDS01IJBS0 KitchenAid Dishwasher - Instructions

I noted that the replacement kit had two large rollers now vs the original that had only one that rotated, the other fixed. Also, the plastic attachment for the door arm was more simple. It was very easy to pull out the unit, attach the spring end hook to the rear of the dishwaser frame hole, attach the new cable, thread it over the two rollers and pull the spring using the cable to attach to the door arms. Less than 20 minutes to install both sides.

Latch handle broke at each side. Beware in Model number of dishwasher that "I" looks an awful lot like "1" and there are both. Ordered the latch handle and it came in good time. Removal of the upper panel was just six T15 torx screws. Of course I didn't have that size, had to buy one. Remove the spring(s). I used small needle nose pliers. When apart it was clear I needed one of the small springs. Found one locally for six bucks. Both "legs" of the handle were broken. It came apart with a bit of figuring, new handle went on more easily than I expected but you have to see how it goes together. Installed the two small springs..be careful, I lost one for a few minutes..with small needlenose pliers. It all went back together easily when the new handle was put through the slot. Reinstalled panel.

Disconnected the water line after removing all the screws which hold the dishwasher in place. Slid the unit out around 24 inches and removed broken Door balance pulley and replaced both sides with the new door balance set . replaced both sides to ensure an even and balanced tension when opening and closing the door! Over all a relatively easy repair. Just be certain you disconnect the water line if you do not have enough slack when pulling out the unit from the cabinet. Good as new!

Ordered the gasket on line. Received gasket in 3 days. Removed old gasket by pulling out in one piece. Pressed the new one in with my fingers and it fit perfectly and now have no leaks. Very easy fix.

Pulled out, put on it's side. Take pump off and put new one on and put all back together. Very easy. Video was helpful also.

After inspection I found the rubber seals on the feed tube for the upper rack to be worn. At that point I thought that was it. I ordered the feed tube assembly the upper rack seal and the lower spray arm support hub as the bottom of the existing hub was worn. Installed all parts and same issue. Researched again on parts select and checked food chopper and it was clogged and broke off. Ordered and it works great. About 100.00 for parts and total time 1 to 1.5 hours as I worked on it three times. Down time about one week. This model is a Whirlpool Superba with the closest replacement about 1000.00 Thanks PART SELECT

Just had to take several screws out of old panel on dishwasher. Used the same screws to put on the new stainless panel. No wires to disturb. Was very easy. Works like a charm. Thank you Parts Select.

Old gasket was broken in places and old. Installing the new one was easy- no tools required. Just pull out the old one and press in the new one. Washer still leaks because door does not close all the way- need to figure out how to get it to shut tight. Maybe the latch is loose or worn.

Followed the video and changed it out in 20 minutes which did not fix the problem entirely, but I went back to the list of symptoms and watched a video on exchanging the Chopper assembly. I disassembled the interior and found broken glass and wire and string restricting the rotational functions. No replacment was necssary here, but a good cleaning was in order. This made it run like new and the glasses came out shiny again. These step by step videos have even made me think about becoming an appliance repairman. LOL! This is about the 8th time I have had success with Part Select. I have had no failures. Thank you for giving away all the secrets. YOU DEFINITELY HAVE SAVED ME AND MY FAMILY TONS OF MONEY!

I had turbo zone on my dishwasher. Stupidest thing ever. It just cut out the water going to the upper rack. This part got rid of turbo zone, and now my dishwasher works like a regular one (much better).

Snap in the upper wash arm and snap on the holding pin. Some bending required.

Removed under countertop screws and lower trim plate. Retracted levelers to clear slate floor. Could only pull unit out about 8 inches, so had to reach in blind to remove and reconnect link ends from springs. Other than my 1 year old Newfoundland pup 'helping', no problems. Parts were perfect fit, just like in the video.

Pulled the machine out and repaired it. Perfect.

The best way to do the repair is watch the video. Because the replacement part was newer than the original it was configured a bit different. The video CLEARLY explained that so it eliminated any angst.

This was the first time I did business with PartSelect but I guarantee you it won’t be the last.
1. They tell you what part to purchase
2. They ship it to you fast
3. The VIDEO gives you clear step by step instruction

First, I viewed the video on the Partsselect website. I pulled the dishwasher from under the counter. When installing it, I had used a six-foot-long braided supply hose, so that didn't need to be disconnected. The drain hose was disconnected at the sink drain connection. Only the wiring connection had to be undone under the dishwasher, so ensure the power's off to the dishwasher. Changing the links was a matter of removing one screw on each side, pivoting the pulley assembly forward, removing it, reversing that procedure to install the new one, and hooking the link at both ends. The door works perfectly and silently now.