Models > KUDS01DJSS0 > Instructions

KUDS01DJSS0 KitchenAid Dishwasher - Instructions

All installation instructions for KUDS01DJSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDS01DJSS0
76-90 of 797
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Pump Motor not working

  • Customer: GLENN from CHEPACHET RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 7 of 7 people found this instruction helpful
1, I shut off ac circuit breaker.
2.Shut off water supply valve.
3.disconnected water line from inlet valve.
4. disconnect the drainage hose.
5. have plenty of towels to mop up water.
6. Remove racks and disconnect water diverters inside the tub.
7. remove phillips head screws that hold dish washer to counter.
8, Pull out DW and lay on its side to expose bottom of dishwasher. disconnect the motor terminal plug. and disconnect the temp prope.
9. disconnect the drainage tube and then proceed to remove the 3 plastic clips that hold the pump housing to the tub.
10. I used some silcone grease around the new pump housing to be safe. then I installed the new pump housing and motor in the reverse order.

It probally took me about an hour start to finish, the hardest part was placing new housing back in. The ring around the bottom of tub is very sharp!
Left some blood there.

No power to dishwasher

  • Customer: John from Chula Vista CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 7 of 7 people found this instruction helpful
First I shut off the breaker for the dishwasher. I had to remove the 6 screws that hold the top part of the dishwasher door to find the panel with the fuse. Then following the instructions that came with the new fuse I cut the wires from the old fuse to remove it. Next I installed the new fuse and attached the wires and then replaced the screws. Turned the breaker back on and everything worked great.

Rinse aid dispenser was leaking

  • Customer: Mark from Austin TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
First I removed the screws holding the outside door panel to the inside door panel. Next (at this was the tricky part) was separating the panels. In our model of dishwasher, there is a layer of Styrofoam between the two panel to reduce noise. Unfortunately the Styrofoam is glued to both panels. Separating it without damage was not possible. So it was done with brute force and the Styrofoam broke in several places.

Replacing the dispenser involved removing six screws, disconnecting the wires and popping the dispenser out. The new one went in easily although there seemed to be a correct amount of tightening to do. It was tricky to get the cover back on because the Styrofoam pieces had to go back together like a puzzle.

Once reassembled, I ran the machine and it leaked at the dispenser. So the cover came back off. This time I played with the adjustment of the dispenser, testing it with the outside cover off, to insure that I had a tight, non-leaking seal. Once done, I put the cover back on and we are back in business.

The new dispensers do not have connections for the "Add Rinse Aid" light. They use a visual indicator on the dispenser itself. I simply taped the wire for the indicator light up and left it inside the door.

One last note, on our unit, the outside door panel is two pieces. I needed only to removed the lower portion for this repair. Unfortunately, I removed both and in the process broke the small plastic end on the door latch requiring me to purchase a new one. Bummer. That was a 10 minute repair though.

motor was very loud...........bearings in motor were beyond repair

  • Customer: Mark from Plymouth WI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 12 of 23 people found this instruction helpful
Replace motor/pump assembly

Lower rack was rusting, staining dishes.

  • Customer: Hugh from ESCONDIDO CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
Rolled out old, rolled in new.

Replace lower dishwasher rack due to broken tines

  • Customer: Daniel from River Falls WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.

quit pumping water

  • Customer: Robert from West Middlesex PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

DISHWASHER UPPER RACK FALLEN ONE SIDE

  • Customer: Gordon from Lynchburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
POPPED THE OLD HOUSING APART WITH SCREW DRIVER, SAVING INTERNAL PART, INSTALLED PART INTO NEW HOUSING, PLACED IN POSISTION, INSTALLED TWO NEW SCREWS AND IT WORKED LIKE CHARMED. SO SIMPLE, I HAVE ORDERED 2ND PART TO REPLACE OPPOSITE SIDE WHICH IS NOT YET BROKEN. THANKS TO THE TERRIFIC PHONE ASSISTANT WHO CONVINCED ME IT WOULD WORK AND NOT HAVE TO REPLACE THE ENTIRE RACK WHICH WAS SUGGESTED BY A REPAIR MAN......MANY THANKS! ! ! !

upper spray arms were not working

  • Customer: Robert from Upland CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Discovered through internet that it may be a bad chek-valve, Opened washer up and removed inside covers. Actually found that the chopper assembly was bent and non-functional. Ordered new assembly plus ordered a new check valve since the other was 8 years old. replaced both at the same time. Dushwasher works like new once again.

R Draper

Door would not latch.

  • Customer: WILLIAM from BUENA pARK CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Partial disassembly determined thar the plastic handle was broken and a tensnioning spring was missing (had fallen out of reach within door) Ordered new replacement parts and received next day. Great delivery service. Installed in short time by removing four screws, disconnecting two wires and reversing procedures to reassemble. Finding parts on line was a great help and the delivery service was great,

dishes in the upper rack were not clean

  • Customer: mike from erlanger KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
it was really easy i removed the lower spray arm then
i removed the four hex head screws that hold on the
fine mesh screen then i pulled out the plastic insert
which exposed the cover to the chopper assembly
removed a smallhex head screw pulled off thecover
and there was the chopper and checkvalve replaced
both with a new one and the dishwasher works like
new thanks a lot im sure a service call would have cost over a hundred dollars

Dishes were not cleaned properly, residue

  • Customer: Francis from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 7 of 9 people found this instruction helpful
I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit so the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.

Door handle was sticking in an up position

  • Customer: Brian from Charlotte NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
First, turn the power off as you need to access the door handle from inside the control panel. There are six phillips head screws that hold the control panel onto the door. These screws are accessible from inside the door. There are two at each top edge and one on each side of the door latch. Hold the control panel on the front side of the door when removing these screws to insure the control panel doesn't drop and damage the control wiring. Once the screws are removed, tilt the control panel away from the door to access the inside of the panel. The latch assembly that the door handle attaches to will come free with a little wiggling (no screws here). Once free, the door handle is pretty easy access. It snaps into place so removing the old one a installing the new one is a snap. Removing the two wires connected to the switch on the latch assembly made things a little easier.

blinking light above cancel button

  • Customer: Damion from Plant City FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
I replaced the electronic control board,

Noisy door

  • Customer: John from Minden NV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.
All Instructions for the KUDS01DJSS0
76-90 of 797