Models > KUDS01DJSS0 > Instructions

KUDS01DJSS0 KitchenAid Dishwasher - Instructions

All installation instructions for KUDS01DJSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDS01DJSS0
31-45 of 832
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishes were not getting clean / Low Water Pressure

  • Customer: Greg from Virginia Beach VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 19 of 21 people found this instruction helpful
Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.

Pump Motor fwd bearing worn out

  • Customer: Thomas from Massapequa NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 18 of 18 people found this instruction helpful
My dishwasher motor was getting very noisy lately and finally died altogether. (the fwd bearing and seals had worn out. There was a small pile of what looked like white sand under the motor from the wear) I removed the dishwasher from the counter after turning off the power at the breaker box. I then turned the dishwasher on its side. The pump motor is removed by first removing the electrical connector, then loosening the retaining bolt and twisting the motor counterclockwise about a quarter turn. The gasket required a little force to become unseated from the housing but not to bad. Wiggle and pull! Be sure to take a look at the alignment at this point to facilitate reinstallation.To install the new motor, align the mark on the impeller(small delta) with the mark on the motor. Insert Motor into housing and turn clockwise one quarter turn till retaining bolt hole is aligned. Install retaining bolt. Be sure to note the position of the stainless steel screen where you insert the motor. Place it back in position before installing the pump if it is disturbed. I lubed the oring with vaseline prior to install also. The new oring was diffrent and did not feel very tight when i installed , but there were no leaks and the dishwasher is running like new. Partselect had the part at my door the next day with no upgrade in shipping charges and I will use them in the future. This forum helped me choose them and made the task easier to do. Hope this helps you as well.

Top spinner fell off with each wash cycle.

  • Customer: Dayna from Fridley MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 18 people found this instruction helpful
The upper spinner fell off with each wash and I had been putting the pointy tac-like piece back into the washer type piece, but they did not hold. I ordered the whole kit (spinner was not needed but came with the set). The tac-looking part was the problem, it had been worn down with use. When pushing the new pieces together to hold the upper spinner back in place it was 100% fixed. Took about 10 seconds. Good luck!

Leakage along bottom of door panel during wash/rinse

  • Customer: Carl from North Haven CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 18 of 19 people found this instruction helpful
The air inlet strip has a flap and two smaller side flaps that seal the bottom of the inner door to the bottom pan that hold the water. The flaps don't form a watertight seal as they only serve to prevent the water surging during wash and rinse cycles from splashing out of the bottom pan onto the floor under the door. What I learned after dismantling the door is that the problem I was having with water dripping from the bottom of the bottom of the outer door was being caused by a loose upper round louvered vent and not he lower vent strip. If the lower vent strip were the problem, water would leak from the front lip of the bottom pan, which is located well behind the face of the front door panel.

Here's my recommendation on the lower vent srtip repair. Turn off the power to the unit at you breaker panel. The air inlet strip is fastened to the backside of the inner stainleess steel door panel. To access the screws the outer door panel must be removed. Open the door and remove the six torx head screws that fasten the outer door panel to the stainless steel inner door. Don't remove the two torx screws top dead center as they hold the door latch. After removing the screws, raise the door up to the nearly closed position. Lift up the outer door panel handle and door bottom to disengage the outer panel from the inner stainless door. The next part is a little tricky since the vent strip hex head screws are at he bottom of the stainless door panel, facing out with the door closed. The lip of the bottom stainless pan is high enough to make it a tight fit to access the screws. There is also a steel bracket that is a door stiffener and holds electrical wiring. I found removing the bracket held by a 1/4" hex head screw on each side made access to the vent strip scews easier. Lay flat on the floor. With a 3/16" nutdriver or socket wrench each of the five vent strip screws can be removed. It's a tight fit between the bottom lip and door bottom, but it can be done. Remove the old vent strip and attach the new one. Make sure it fits snugly into the slot. Best to have an extra pair of hands at this point to hold the stip securely in place while screws are reinserted from the opposite side. Reassemble everything in reverse order.

It was when I had the outer door panel off that I noticed my problem was water getting past the upper round louver vent seal and thus running down the inside of the outer panel. Simple fix was to remove and clean the scale residue from the parts and door. Then reassemble the vent and twitst tighten the vent to compress the rubber seal on the inside face of the door.

dishwasher leaked from left side of door

  • Customer: Russell from Bellevue WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 19 people found this instruction helpful
As I pulled out the old rubber gasket I noticed there was a flat side and a curved side, this is how the new one must go. When I put in the new gasket in I just made sure the flat side (faced out) and it really was very simple. It just fits inside a grove, very easy to install. I compared the to parts (old and new) they were exactly the same shape and length.
I was very impressed with the web site navigation and layout. I was able to zoom in on pictures of the part and there were exact measurements of dimensions.

The Door Just Falls Down

  • Customer: Neil from Winchester VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 24 of 38 people found this instruction helpful
After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!

Dishes would not clean

  • Customer: Kathryn from Gordon NE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 18 of 22 people found this instruction helpful
Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.

Removed & Replaced Detergent Dispenser

  • Customer: Raymond from Lancaster CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 17 of 20 people found this instruction helpful
Via your web-site I was able to download the step-by-step screen-shot pictures. I was really surprised on how easy the detailed photo screen shots made the repair really easy! Thanks for making this repair a piece of cake. If I should ever need additional parts for any of my home appliances I will certainly order my parts through PartSelect.

dishwasher display would not power up nor turn appliance on.

  • Customer: Jane from Carson City NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 14 of 14 people found this instruction helpful
Following advice given on website by previous customers I was able to remove 6 tork screws and check the fuse which was okay. Proceeded to remove the control board and found significant burning on the bottom side. Ordered a new board online Sunday night, shipped Monday by two day Fed Ex, arrived Weds. morning and installed it in less than 10 minutes. Fair price, excellent service and shipping. Thank you and I would buy from you again.

Plastic clasp on door spring broke

  • Customer: Stephen from Galt CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 14 of 14 people found this instruction helpful
Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

No power

  • Customer: Scott from Chisago City MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 14 of 15 people found this instruction helpful
Replaced electronic control panel first which had an obvious defect (burned terminal). Still no power. Replaced fuse and works fine now. Took lots of reading to find out the dishwasher had a replacable fuse. Even the appliance store didn't know.

Detergent / Rinse Dispenser did not function. Detergent door would not close

  • Customer: Pamela from Saint Peters MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 15 of 18 people found this instruction helpful
Replacing the actual part was easy. Getting to it was the slightly difficult part. Here's how it went:
Remove the torex type screws surrounding the inner door - this was the easiest part. The screws came right out, but be careful. Removing the screws near the top (was controls) part will release the seaparate top part. Once you do that, it's only held by wiring, and you don't want that to break, so treat this part with care.
Remove the bolt screws holding the outer door to the inner door - so the inner white door containing the dispenser to be replaced, and the outer door separate, but are held together by these bolt screws. You need to remove these to separate the doors further giving you easier access to the dispenser. Some of these bolt screws were in challenging positions to reach.
Disconnect dispenser wiring and replace part - Remember where the wires go, so mark them before removing them. The part is held in by 6 bolt screws. Once removed, the part easily came out. Pop the new one in, screw the bolts in, plug the wiring back up.
Put all parts mentioned previously back together.

Now even though we gave the correct model # of our unit, the part sent did not match 100% what we replaced. There was an extra wire plugged to ours. The connector to plug it to does not exist on the new part. My assumption is this wire is for detection of rinse agent (illuminates a ligth on the front panel if empty) - so we just left this unplugged. The new part has a manual, visual gauge on it anyway which I prefer, so this was not a big deal. This is just warning for others that do this kind of thing.

All in all, it was a well worth it repair. $50 as opposed to $500 for a new unit and installation. We will definitely be looking to this site again for items we feel can be repaired. THANK YOU!

Water leak / minor hard to find

  • Customer: Gus from hayward CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Wrench set
  • 15 of 19 people found this instruction helpful
First: Turn power to the Dish washer OFF, then remove the two panels at the bottom of the dishwasher.
Two: remove the Door face panel for easier access to the inlet-Valve.
Three: remove screw that holds Inlet-valve bracket.
Four: slide Inlet valve bracket left and back to get out of slots.
Five: Holding the Inlet-valve forward loosen and remove water line (copper tube nut / pressure fitting).
Six: Remove two wire clips
Seven: Remove platics hose (Spring Clamp)
Replace Inlet-Valve and reverse process///

Machine was not cleaning properly. insufficient water to the top shelf

  • Customer: John from Rockport ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 17 people found this instruction helpful
I cleaned the chopper and screen a few times and it continued to get blocked after a couple of cycles. Replaced the chopper assembly and now it works find.

Stopped Running,Will Not Start, and Clean LED Blinks 7 times then repeats

  • Customer: Deb from LaPorte IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 14 of 18 people found this instruction helpful
Got Maintenance Flyer out an read about problem
Removed access plate
Disconnectd water and drain
Removed anchor screws
Pulled unit out and disconnedted from Electric
Flipped on it's back
Ohmed out all heat related items and found discrepency with Thermisitor resistance
Ordered and received Part
Changed out Thermisitor
Checked wiring to Heater and replaced connections
Hooked electric up
Ran Diognostics per Maintenance flyer and cleared fault
Hooked back up and ran like a champ

The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem
All Instructions for the KUDS01DJSS0
31-45 of 832