KUDS01DJSS0 KitchenAid Dishwasher - Instructions

Removed the dishwasher from under the counter, disconnected the copper water tubing, placed it upside down, removed the old pump and replaced with new. The only iffy situation is making sure the copper tubing doesn't kink when removing the dishwasher and putting it back into the cabinet. Very simple, my husband can fix anything. Your video was very helpful as well.

Per the instructional video on your website. It was accurate and presented clearly.

Just put it in by hand and pressed the clips together. Couldn't have been faster or easier. Fast delivery too. Thanks so much!

I was only able to get the dishwasher partially out from under the counter. I had to reconnect the springs using a big screw driver. I then attached the door portion of the cable to the door and pulled the spring back to connect it. It went OK. I found your video valuable because I knew what I was dealing with and was able to come up with a solution for not pulling the washer completely out

Door balance kit was very easy to repair. Washer was installed incorrectly with water service run through the units frame. Once this issue was addressed, ordering and installation was a piece of cake.

Removed screws around the door, unplugged the solenoid,lifted the tabs on the dispenser and removed the dispenser. Installed the new dispenser, plugged the solenoid back in and reistalled the door screws. ran the dishwasher and the same issue still happened. I removed the water fill valve, I cleaned the inlet screen and exercised the plunger. I hooked up the water supply to it and gave it a 120v supply power to it. I don't recommend to the average homeowner to do what I did, I am an experience tech. The water valve worked everytime I applied power to it, I reinstalled the water valve but I haven't ran the dishwasher yet. If the problem continues, then it must be the electronics. It will be cheaper to replace the diswasher due to it being 8 yers old.

Well, I could not afford a repairman, so when I learned that their was a fuse kit in the dishwasher. I decided to start there. I ordered a fuse kit from PARTSELECT, got the part the next day and installed it myself inside control panel. BINGO,DISHWASHER FIXED,I WASHED A LOAD OF DISHES !! HAPPY :)

purchased the correct seal, opened the door and pulled out the old one with one motion. marked the middle on the new one then installed with a little bit of pushing into the slot from one side to the other. making sure to tuck the ends into the recess at bottom of each end and clip off the excess and done! but make sure you replace the lock tab on the top when you replace the seal!!! it comes with it but you will have to slide the washer out a bit to push the old one out, There are no fasteners, Just push out and snap in and wala!! dry floor

snapped on new wheel done

Pulled dishwasher out, laid it down on its back. that made eaiser to get to the motor. Pulled the motor off then put the new motor on.

The old spinner arm had fallen off so all I did was remove the piece that held the old spinner in place and clipped the new one in place. The shame of it all is, the old spinner was fine, and even the female end of the attachment piece was fine. So basically I had to buy a $20 'assembly' to get one little piece of plastic. Still, it fixed my problem and even though I shopped elsewhere, I never found anything but the assembly for sale. All-in-all, a good experience from PartSelect.

Just followed the video. Seemed simple enough but the bolt location was different so had to watch the video again paying specific attention to the part where he tells you to use the old bolts to replace the new pulley system. The new pulley system already has a bolt in the top pulley. You will need to old bolt through the bottom pulley. Works great - for now.

Took out Racks, lower spray bar, bottom screen cover, Food Chopper screen cover and the Food Chopper. Old Food Chopper knife wasn't turning and screen was full of food particles. Upon inspection found knife was stripped off the plastic shaft. Replaced Chopper and Presto! Dishes are Clean.

Triped electric breaker, disconected hoses, removed two retaining screws, pulled unit from under counter and turned on side, removed hoses and two electric "Pigtails" then retaining screw and lifted out. Replaced with new valve, and machine, in reverse order.

I watched the You Tube video. Ordered the part. Waited a week for the part to arrive. Snapped the new part in. Done in 5 minutes.