Models > KUDS01DJSS0

KUDS01DJSS0 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDS01DJSS0

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDS01DJSS0, or you can search by name or part description. You can also find your part by where it is located on the KUDS01DJSS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDS01DJSS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$19.16

Door Balance Link Kit

This kit includes 2 door balance links and 2 door balance mounts with wheels.

$6.78

Mounting Bracket

Sold individually.

$19.48

Upper Wash Arm Kit

This part contains the mounting clips and helps distribute water from the top of the dishwasher tub.

$50.25

Door Gasket with Strike - Black

The gasket provides a seal between the tub and the door. The door strike serves as a mechanical actuator for door switch operation and provides door tension for proper seal.

$20.38

Chopper Assembly

This chopper assembly chops/minces the food particles to prevent clogging of the dishwasher pump.

$3.76

Door Release Spring

This spring is located in the door section. Sold individually.

$35.32

Door Handle

NOTE: This part is no longer available in white or biscuit.

$16.46

Fuse Kit

When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.

$50.59

Detergent and Rinse Aid Dispenser

This part releases the detergent and rinse aid into the dishwasher.

$37.59

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 303 of 309 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 193 of 204 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to th... read more

Controller board replacement

  • Customer: tony from carrollton TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 117 of 125 people found this instruction helpful
Simple task - remove the front door cover to expose the cover for the control panel which is then also removed. Be sure electricity is disconnected from the appliance, then simply remove the old control board (remove the quick-connect wire harness) and slide the replacement board back in. Reconnect wiring harness, replace cover and door panel, then turn-on e... read more