Models > KUDI24SEBL1 > Instructions

KUDI24SEBL1 KitchenAid Dishwasher - Instructions

All installation instructions for KUDI24SEBL1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDI24SEBL1
46-60 of 595
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic handle to unlock door broke

  • Customer: Anthony from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
Took 6 screws off to disassemble the control panel, removed the electonics, removed and ordered handle, and replaced it.

Smooth.

Replace the dishrack, which came unassembled

  • Customer: Delbert from Fergus Falls MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
The dishrack fits perfectly in our 10 yr old KitchenAid dishwasher. Took a little while installing the wheels and 3 rows of tines that were not in place as instruction sheet was a bit vague. Our old rack had had several tines rust off, and recently learned that we should be using liquid detergent as the powder is like a sandblasting agent over time. Also we didn't get a knife/fork basket with the rack; however, old one fit okay.

Plastic handle broke

  • Customer: Paul from Ashburn VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
Removed inside cover and inserted new handle on two tabs and attached latch. Slightly tricky to get 3 pieces in place and reattach cover without them moving.

retainer nut split

  • Customer: Carol from Wolverine MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.

The four Torkx screw studs on the black plastic control panel assembly broke off. The dishwasher was useless.

  • Customer: Andrew from Peachtree City GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
I wish I knew a couple of things before doing this repair. 1) As you take off the panel, remove slowly and pay close attention to how the latching mechanism and spring works, 2) The mylar cover over all of the buttons (the panel that say s "Kitchenaid Superba, on, off, etc) does not come with the panel and costs $45 more. I was determined to save it. I used a flat Xactor blade to separate it from the broken control panel. As careful as I tried to be, I cut it a few times. Had I known I was dealing with a contact cement, I would have known to get it started and slowly peel it off. It will readhere to the new control panel without new adhesive. I replaced the vinyl waterproof cover for the circuit board, and installed the latching mechanism and spring. I positioned the new panel and screwed in the four screws. It works fine.

Water leak at water inlet to tub

  • Customer: William from Austin TX
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Contrary to info on your website, the bezel is removed by turning it counterclockwise. This misinformation wasted a lot of time. The bezel is difficult to turn. I used a home-built wrench: Drive two screws spaced 3 inches apart through a stick of wood, projecting 5/8 inch. Engage the screws in the slot in the bezel and in the grill, and turn CCW. I cleaned the deposits from the surface where the gasket seals with white vinegar. New gasket and bezel fixed the problem.

dishwasher no thoroughly cleaning

  • Customer: Daniel from Chestertown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

Broken door spring

  • Customer: Stephen from Whitesboro NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 7 people found this instruction helpful
One day the door came slaming down. Pulled off the bottom two panels and noticed a broken spring. For the small investment I purchased two new springs and replaced both while I was down there.

1) Pulled off the bottom two panels
2) Took note of location of where the springs were and removed the old springs.
3) With my fingers found the holes and placed new spring on the door side.
4) With some muscle stretched the spring untill it joined the multiple tension slots on the frame of the washer.
5) Found the correct tension to suppt the door opening and closing properly.
6) Replaced the two bottom panels
7) Cleaned up and was done!

Thank you partselect for your great web help!

The spray arm snapped off from the mounting bracket.

  • Customer: Elizabeth from Olathe KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
First of all, we were very impressed with the ease of finding the parts, the ordering, and the velocity in which the parts were shipped. We received them the next day. I had to remove one of the screws from the old kit, since the new one only came with one. I looked at the diagram on the website of the assembly, and also remembered what the assembly looked like before I took it apart. The first time I tried it, I could not get the spray arm to spin without hitting the dishwasher rack. Since I had ran out of time, I had to wait until the next day. Once I started, I realized that I had the mounting bracket on backwards. Once I turned it around, I tightened the screws, and it was done within 5 minutes.

torn graphic panel button functions not visible

  • Customer: Jeffrey from Mountain View CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
Peeled off the overlay graphic. Cleaned off the adhesive residue completely using WD-40. Cleaned surface with parts cleaner for the new stick-on graphic overlay . Cover control buttons so they are now labeled clearly. Press stick-on applique in place & rub surfaces for adhesion.

Dishwasher leaking water

  • Customer: Evan from Hudson MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Install was very easy. Used hands, pliers to pull out old gaskets. Wiped down old dirt in track. Started from (top) middle of door frame and used some soap with warm water to insert new gaskets. That's it! Kept old plastic brackets in place because it was too difficult to remove door springs. Old door seal and lower door seal were badly worn (gummy and falling apart) - Thought that was the issue with the water leaking. Nope, I was wrong. Looks like the tub seal, and the plastic bearing that is under the spray arm. Going to buy new instead of diving in the money pit. 10 years old, motor corroded from water over the years.

Top blade assembly fell off because of broken plastic on spray arm mount

  • Customer: Vera from Highland MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

Dishwasher often didn't fill with water.

  • Customer: Lorrin from Longview WA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 8 people found this instruction helpful
Remove power, either unplug the unit or locate and turn off the circuit breaker. There is power under the dishwasher even if it is not running.

Use the nut driver to remove both lower panels to gain access to the bottom of the dishwasher.

I suspected the overflow switch and used the ohm meter to discover the resistance of the switch, with no water in the washer, measured anywhere from a couple of ohms to 40 ohms or more and of course it should be less than one ohm.

There was no sign of any leakage or other problem so I wanted to keep the job simple and replace only the actual micro switch.

Problem! The micro switch is mounted on the back side of the float stem kit and visibility is severely limited. About all you can see are the switch terminals and the head of the phillips screw that holds the microswitch on the rest of the float stem kit.. You'll definitely need a small mirror.

I first pulled the wires from the microswitch terminals. Then I used a small phillips screw driver to remove the screw holding the switch and the first thing that happened is the small white float lever fell out. (I didn't know that it was even there because of the poor visibility. Ugly surprise!)

I spent 1/2 hour or more studying how the lever went in and found that the cirular end of the lever fits into a circular depression in the assembly body and was HELD IN BY THE SWITCH. (Now it's really getting ugly!)

The problem then is how to get the lever back in place and have it stay there while placing the micro switch back in place. There just isn't any easy way to do that. If only the switch and lever were one piece it would have been so simple.

Aha!

I placed and aligned both the lever and the microswitch on the float assembly body that I received. Using a couple of small pieces of electricians tape I taped the microswitch and lever together so they were one piece. Then I carefully (very carefully) removed the switch/lever
"assembly" that I made and eased it into position onto back side of the dishwasher float stem assembly body. When the switch is almost in place there is just barely room to get the tip of your finger in there and seat the rounded end of the lever into the depression. After seating the lever, carefully replace and tighten the phillips screw holding the switch in place. Then remove the electricians tape.

Replace the wires on the micro switch terminals, replace the front panels, put your tools away, and by golly, you're done.

This repair is not for the faint-hearted nor for those with fat fingers or who tend to be klutsy. It took me three or four attemps and a couple of hours to get the microswitch and float lever into place. But I think it was worth it as I didn't have to remove the dishwasher, play with water lines, or remove the full float assembly thus avoiding creating other problems that might likely result in water leaks and additional repairs..

If you decide to try this repair, good luck. It can be done but it is tough.

dishwasher was overflowing

  • Customer: paul from cambridge OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.

Dishwasher inoperable, thermal fuse blown, door switch OK

  • Customer: Richard from Eugene OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 11 people found this instruction helpful
Turned off the power to the Dishwasher. Removed 6 Torx screws holding control panel cover. Disconnected the connectors to the control assembly. Removed and replaced the control board. Replaced the thermal fuse and the door switch. Reconnected the connectors. Reassembled the control panel cover. Turned on power and tested the DW. All OK.
All Instructions for the KUDI24SEBL1
46-60 of 595