Models > KUDI01FLSS3 > Instructions

KUDI01FLSS3 KitchenAid Dishwasher - Instructions

All installation instructions for KUDI01FLSS3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDI01FLSS3
541-555 of 723
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The spring link cord was broken

  • Customer: Frank from Queen Creek AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I removed the dishwasher from under the counter. Removed the broken parts,replace with new ,and reinstaled the dishwasher under the counter

door balance kit broken

  • Customer: Steven from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I was standing in the kitchen and heard a pop. Unsure what it was, I found an online video explaining that either the spring or the door balance mechanism was the issue. The video explained how to repair the door balance mechnanism so I removed the cover at the bottom of the dishwasher and found the rope for the door balance had broken. I then knew exactly what part to order. I ordered the balance kit from PartSelect and it was delivered two days later. I began the install and found that I could not pull the dishwasher out far enough to reattach the spring that came loose when the rope broke. I could tell something was holding it, but not sure what. Figuring this out probably took the most time. I thought it was stuck against the counter top so I turned the legs down and still couldn't get it out. I then looked at the plumbing and wiring next, but couldn't tell where the wiring entered the machine since it came from the back and you have about 4" of space to look through while laying on your back on the floor. I finally found the electrical box, took off the cover and could see the wires weren't long enough. I had to shut the circuit breaker off, disconnct the wires and pull them out of the box so I could get access to the sides of the dishwasher. Once that was done the parts fit perfectly and I finished up by reinstalling the wiring, sliding it back to its original position so the counter top screws would line up and readjusting the legs so it was at the right height and balanced side to side. The whole job took about an hour and half. If I had to do it again, I would say 30 minutes at the most. Very easy.

Dishwasher door would slam down.

  • Customer: Stephen from Hingham MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The door had no resistance when opened and fall down. Then, after awhile, the door began to slam down when open. So I'm guessing that one of the door balances gave out. Then the other. So I unscrewed the screws on each side of the dishwasher and noticed the broken string on each side. Replacement was simple. Connect the springs to the rear of the dishwasher. Attach the strings to the springs, replace the pulleys with the new ones supplied with the kit and attach the other end of the strings to the dishwasher door. Watch the video for more help.

Top rack of dishwasher not getting water. Chopper blade was kicked off from a piece of plastic that got wedged. Chopper screen clogged.

  • Customer: Christopher from Wayne NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Checked to see if top spinner was clogged. All ok. Wanted to see if water was flowing from bottom. Checked a video to see how to remove parts to access lower area. Saw the problem immediatley. Clogged Chopper screen due to broken chopper blade. Ordered new chopper assembly and got it in two days. Five minuted to install. Washer works like new.

The plastic parts on my door balance kits broke making the door extremely dangerous

  • Customer: Michael C from Pembroke Pines FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The repair was extremely easy as the video was extremely helpful. A word of caution, make sure to watch the entire video before you start. I only watched the video 1/2 way through (as I thought I knew it all). When I (thought) I completed the repair, when I opened the door, polley's went flying everywhere. I finished watching the video and saw that I also had to use the bottom bolts, not just the top bolts. Nothing dangerous, but extremely funny. I then completed the repair W/O a hitch.

Tension cord broke on one side.

  • Customer: Billy from Dalton GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy to replace the two tension cords. Saved a 75.oo service call. The Video was very helpful.

Extreamly noisy Motor

  • Customer: Edward from Malvern PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Unhook electrical/water supply, removed dishwasher, flip upside down, Remove wire connector from motor, remove bolt from motor, turn motor and remove, install new motor in reverse process.

Replaced Circulation Pump

  • Customer: Sanford from Moodus CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled Dishwasher out, turned off power. Did not have to disconnect any hoses or electrical, because when I did the original installation, I left plenty of slack, so as to be able to pull it out. Next, tipped it on it's side, unplugged the harness, undid the bolt, turned motor 1/4 turn, pulled it out. To, re-install, just reversed the process. About 1 hour.Followed Excellent instructions on video. Was very impressed with delivery time. Only about 30 hours, from the time I ordered, to receiving part. Reg. ground.

top rack dishes not clean

  • Customer: Thomas from Moline IL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Estamated time was 15 minutes, it took me about 3 hours because everything was so cake up with detergent. Parts would not move. Video very helpful

wouldn't run / push pad lights out

  • Customer: Ned from Hamburg NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took apart upper panel from inside of door (6 trox head screws) disconnected wiring harnesses, removed curcuit board, backside appeared to have fried. reinstalled new board. started washer run's fine

Plastic cable broke due to age/wear.

  • Customer: John from Benicia CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I noted that the replacement kit had two large rollers now vs the original that had only one that rotated, the other fixed. Also, the plastic attachment for the door arm was more simple. It was very easy to pull out the unit, attach the spring end hook to the rear of the dishwaser frame hole, attach the new cable, thread it over the two rollers and pull the spring using the cable to attach to the door arms. Less than 20 minutes to install both sides.

left side door balance repair

  • Customer: Nino from Neshanic Station NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Disconnected the water line after removing all the screws which hold the dishwasher in place. Slid the unit out around 24 inches and removed broken Door balance pulley and replaced both sides with the new door balance set . replaced both sides to ensure an even and balanced tension when opening and closing the door! Over all a relatively easy repair. Just be certain you disconnect the water line if you do not have enough slack when pulling out the unit from the cabinet. Good as new!

Dishwasher smelled and not cleaning dishes

  • Customer: Mark from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video was excellent as was my experience when I replaced my ice maker.

Old motor making lots of noise. Replace with new one!

  • Customer: Kathy from Northfield MN
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Pulled out, put on it's side. Take pump off and put new one on and put all back together. Very easy. Video was helpful also.

track stop broke

  • Customer: Denise from Chico CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
put new one in
All Instructions for the KUDI01FLSS3
541-555 of 723