Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDI01FKSS1

KUDI01FKSS1 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDI01FKSS1

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDI01FKSS1, or you can search by name or part description. You can also find your part by where it is located on the KUDI01FKSS1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDI01FKSS1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.66

Door Balance Link Kit

This kit includes 2 door balance links and 2 door balance mounts with wheels.

$16.69

Fuse Kit

When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.

$15.76

3rd Level Wash Spinner Kit

This part is the top spinner located at the very top of the wash tub. Water passes through all the spinners causing it to dispense all around the tub.

$124.79

Lower Dishrack

Dishrack ONLY.

$56.91

Door Latch

As per the factory, this is an updated latch and you will need to order the strike as well - as per your model number.

$102.79

Circulation Pump and Motor Assembly

The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.

$62.16

Door Seal

This gasket comes with the adhesive.

$7.22

Touch-Up Paint - White

18ml

$12.72

Drain Hose

This drain hose is 6 and 1/2 feet.

$43.41

Float Switch Kit

This kit includes the switch, lever, seal and standpipe. Water that fills your dishwasher lifts the float, and when it reaches a certain level, the float acts as a trigger for the float switch. The float triggers the switch to shut off, thereby shutting off the flow of water into the dishwasher.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Worn dishrack wheel mount

  • Customer: Jason from Todd, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 499 of 508 people found this instruction helpful
This wheel mount broke from normal use and made the upper dish rack disconnect from the sliding arm that extends it outside the dishwasher body so that you can fill it. The part was delivered quickly and was easy to install using just a screwdriver to loosen the retainer clip on the end of the extension slide. Once the retainer clip was removed, the new part... read more

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 443 of 454 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

The wheel mount had broken so that the wheel was disconnected from the mount on the upper rack, making the rack unstable.

  • Customer: Elizabeth from San Francisco, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 381 of 389 people found this instruction helpful
I had to fiddle with the mount a bit to get it on the rack properly. Then I pulled back slightly on the inner part of the end piece of the track while also pulling the top of the piece back and released the inner tip of the piece, allowing the end piece to be removed. I placed the new wheel in the track and replaced the end piece.

Super easy and... read more