Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDE70FVPA0

KUDE70FVPA0 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDE70FVPA0

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDE70FVPA0, or you can search by name or part description. You can also find your part by where it is located on the KUDE70FVPA0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDE70FVPA0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.53

Door Balance Link Kit

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwashe...

$44.41

Silverware Basket - Gray

The silverware basket is a holder for washing flatware or silverware in your dishwasher. Note: This part has been updated by the manufacturer, it may appear different but will still function the same. This basket is gray in color. To do this repair, open the dishwasher door and slide the bottom rack out. Discard of the old basket. The new basket will sit in place with two hooks on the back that will catch onto the rail. Tip: to prolong the life of your basket, keep the sharp end of your cutlery pointed up to prevent cutting through the bottom, and gently place instead of dropping.

$5.07

Tine Pivot

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. The clip is used to keep the tine row in place in the dishrack. ...

$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

$19.54

Bi-Metal Fuse

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit i...

$26.28

Tine Row

The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is damaged, you should consider replacing it. This product is made of gray plastic and is approximately 21 inches in length. This tine row contains 11 straight tines and 1 curved tine. This product is sold individually. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the old tine row and replace it with the new one.

$15.03

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$15.70

Rinse Aid Cap

This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.

$51.16

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 521 of 535 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 284 of 314 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more

water leaking out of bottom of machine

  • Customer: MICHELLE from EDEN VALLEY, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable), Wrench set
  • 162 of 181 people found this instruction helpful
removes the 1 screw that held the old one in and removed the water lines the supply line with a adjustable wrench and the internal line had a hose clamp on it then i just went in reverse... read more