Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDC01TMWH6

KUDC01TMWH6 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDC01TMWH6

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDC01TMWH6, or you can search by name or part description. You can also find your part by where it is located on the KUDC01TMWH6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDC01TMWH6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.53

Door Balance Link Kit

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwashe...

$16.03

Upper Rack Wheel with Mount

This wheel and mount assembly is located on the upper dishwasher rack. They are sold individually and four are usually required for your model. Also known as stationary wheel mount.

$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes ...

$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

$4.46

Upper Rack Wheel and Mount Assembly

Sold Individually.

$25.95

Chopper Assembly

This chopper assembly, or dishwasher drain food chopper, chops food particles into small pieces to prevent the dishwasher pump from clogging. If your dishwasher is making grinding, rattling, or humming noises, replacing this part may solve the issue. Other symptoms include not draining, low water pressure, chopper not working, or the dishes not being cleaned. The tools needed for this repair project are a #15 torque spit, #20 torque spit, small flat blade screwdriver, and needle nose pliers. Make sure to unplug your dishwasher from the power source before beginning installation. Refer to the manual provided by the manufacturer for further instructions.

$41.83

Door Handle

NOTE: This part is no longer available in white or biscuit.

$55.07

Detergent and Rinse Aid Dispenser

This part releases the detergent and rinse aid into the dishwasher.

$3.46

Door Release Spring

This spring is located in the door section. Sold individually.

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 526 of 540 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 297 of 316 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to th... read more

Controller board replacement

  • Customer: tony from carrollton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 196 of 217 people found this instruction helpful
Simple task - remove the front door cover to expose the cover for the control panel which is then also removed. Be sure electricity is disconnected from the appliance, then simply remove the old control board (remove the quick-connect wire harness) and slide the replacement board back in. Reconnect wiring harness, replace cover and door panel, then turn-on e... read more