KUDA03CTWH3 KitchenAid Dishwasher - Instructions

I viewed the online video where the installation procedures were presented. Removal of the dishwasher from the counter was very easy since it was retained in place by two small screws attaching the top of the appliance to the underside of the counter. The appliance could then be pulled out into the kitchen sufficently to reach the springs on the lower sides. A thermal insulation blanket covered the appliance and had to be lifted to work on the lower side of the dishwasher. One spring was adrift beneath the appliance and its detachment was the loud SNAP that I heard. The spring was easily recovered and reattached to the rear of the appliance and then then working one side at a time I first removed the old parts and reinstalled the door balance link to replace the broken cord. I then changed out the other side to complete the job.

Pulled the old seal out and inserted the new one. Very simple and fast. Dishwasher no longer leaks.

Removed the motor and installed the new one. Dishwasher works like new. The old motor was in vary good condition if the bearings and seal could be replaced. It is a shame there is not a place to send them for re-manufacture rather than salvage. The cost for new material and labor to produce a new one must be greater than re-manufacture.

Real easy there was no guess work after watching your video on how to change the door balance kit. Having that video on the same page that I ordered the part was a great Idea. The guy that thought of that should get a Raise.

I followed the on line video instructions and the repair was completed with a hitch. The seal did not display the 'white stripe', but the enclosed illustration cleared up any question I had about proper insertion. The part arrived within 24 hrs of shipment! I will use Parts Select exclusively in the future! No more big bucks to have a Sears guy simply plug in a new part.

Repair was very easy...Thank goodness for the viedo...The part came the next day...I would recomend looping the link first...then attaching it to the spring.....

It was easy to identify the needed part on the web site. We ordered it, and it arrived in less than a week. The part was easy to slip into its place in the dishwasher, and the rack now stands up as it should. Couldn't have been easier.

Excellent, Very easy to repair and the video showed me how to do-it-myself.Thank you

The hardest thing in installing the pump was pulling the dishwasher from under the counter. Once that was done and the mess with drain hoses and supply hoses was cleaned up, all it took was undoing one bolt to turn and remove the motor by turning in counter clockwise. the seal comes with the new motor and don't forget to reconnect the wire harness to the new motor on re-assembly.

1.opened the door removed the two anchoring screws at the top of the dishwasher. 2.slid out the machine, layed it on its side on a towel for water spill. 3.unplugged the old motor. 4. used 1/4 inch ratchet with 6 inch extension and 3/8 inch socket, removed the mounting bolt. 5. twisted the motor clockwise approx. 1/4 turn and removed the old motor with impeller. 7. repeated reverse method to install.

I ordered a repair kit and replaced the cord linkage without any tools other than those to pull the bottom panel and screws from the top retainer clips. Great instructions and extremely easy repair myself. Thank you.

Removed torx screws from rear of door. Openned door assembly and replaced board...very easy...about twenty minutes total. It's working fine and we're looking for years of additional service.

I cut the breaker and disconnected the in and out water lines, then removed the washer. Once on its side, I took it apart until I found what was broken. The chopper unit had broken and parts were sucked into the pump. After going online and finding/ordering all the parts, I cleaned everything and put it back together so as not to lose anything. When the parts came in,it was an easy job to replace the broken parts and have it back in use. The repair would have cost over $350 and my parts bill was less than $90. Thanks

I looked on your website under our model number. There I found various descriptions for the problem I had. Under the problem column, I found the possible parts needed. Turns out I needed new door pulleys and ropes. We watched the video provided by your site,pulled out the dishwasher, and changed out the ropes and wheel assemblys. Squeak is gone, door is balanced. Mission accomplished!

Replaced basket. I couldn't believe that I received the basket the next day. Your service is 1st class and the person I talked to was pleasant and efficient. Your website to find parts is great!