Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUCS02FRPA0 > Instructions

KUCS02FRPA0 KitchenAid Trash Compactor - Instructions

All installation instructions for KUCS02FRPA0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the trash compactor repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUCS02FRPA0
46-60 of 118
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

motor gear broken

  • Customer: Clem from Scottsdale, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 3 people found this instruction helpful
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Plastic Gear Wheel Broke

  • Customer: Reagan from Glenshaw, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 1 of 3 people found this instruction helpful
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.

Smelly kitchen

  • Customer: Saralyn from Dahlonega, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Removed the old filter and screen and replaced with the new!

Compactor ram was stuck in the down position and door would not open

  • Customer: Michael from South Boston, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

lost cover (went into trash)

  • Customer: Jacek M from Bedford, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
replaced

Broken Drive Gear

  • Customer: Michael from Painted Post, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 4 people found this instruction helpful
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

Ram quit moving

  • Customer: Hal from Granada Hills, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Removed bottom and replaced gears

switch broke off and would not activate compactor

  • Customer: Jane from Edmond, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
removed two screws and replaced broken piece. Only thing a little difficult was getting screws in tightly enough to hold piece secure.

actuator broke at base. base remained in place.

  • Customer: Douglas from Moorpark, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
Opened the compactor bin. Removed the failed actuator base (two screws) using hardened phillips # 2 screwdriver. prepped the new part holes by inserting the screws into (too small on replacement part) holes prior to installing(used needle nose pliers to hold part while prepping holes). Backed out screws from replacement part then installed part with same two screws using hardened phillips # 2 screwdriver. Tested functionality and received hug from son's grateful wife. P.S. I printed the parts diagram showing the part relationships from the website. Very helpful in repair planning. Recommend this to all. Do not know why the two rubber grommets were included in kit as they seem to apply to the horizontal screws securing the pedel itself that the actuator is installed on and are not needed for the repair.

Regards,

DougM

Bought a washer without front leveling feet

  • Customer: Rick from Lennon, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 2 people found this instruction helpful
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

unit was missing parts

  • Customer: Richard from glendale, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 5 people found this instruction helpful
Installed new parts. Worked fine.

Switch activator broke

  • Customer: John R. from Cocoa, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
Replaced the broken part with a new part by attaching with 2 small sheet metal screws.

Broken Part

  • Customer: Francisco from Hernando Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 6 people found this instruction helpful
Part replacement

Trash compactor does not actuate

  • Customer: MILIND from BEAVERTON, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 6 people found this instruction helpful
Very simple. 2 screws to unscrew - and then screwed the new actuator in. took less than 10 minutes.

Could not activate the compactor

  • Customer: Dan from Ramona, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
It simply required removing two screws that were holding in the remaining piece of the broken actuator, positioning the new actuator, and reinstalling the screws.
All Instructions for the KUCS02FRPA0
46-60 of 118