Models > KUCS02FRPA0 > Instructions

KUCS02FRPA0 KitchenAid Trash Compactor - Instructions

All installation instructions for KUCS02FRPA0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the trash compactor repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUCS02FRPA0
16-30 of 117
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The compactor keeps on making noise at the end of the compactor cycle with shaking until the "off" switch is pushed.

  • Customer: Paul from Sandy Springs GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Took off front panel and replaced the directional switch which I thought was the problem. However, the problem continued. I read on line it could be the "centrifugal" switch on top of the motor. I haven't gotten around to taking it apart yet to see if that is the problem because it is more involved down under and in the back. That switch cost $88.
Any suggestions from others?

Light switch broke on refridgerator door.

  • Customer: Darlene from Holland MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
I measured the part then looked for a similar switch that might work. I was so happy to find the exact part we needed for our 24 year old refridgerator!! I was so impressed with your slection of parts and best of all I had the part in 2 days! You are in my "favorites" just in case I need you again!

Thank you

The light would not turn on when the refrigerator door was opened

  • Customer: Edward from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
I removed the plastic portion to get to the switch and wires. I removed the old switch by disconnecting the two wires and pushing it out of its setting.

I discovered the old switch only had 2 prongs where the new switch had 3. Once I figured which 2 of the 3 prongs would light the lightbulb,
I then connected the two wires to the correct prongs of the new switch. I pushed the new switch into its setting and replaced the plastic portion on the refrigerator. Voila, success. The refrigerator door now comes on when its door is opened.

Thanks for the having the part and getting it at our door step in 3 days.

plastic gear broke this is the 2nd time in less than 1 year so this is the 2nd repair

  • Customer: Mary from Lilburn GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 5 of 8 people found this instruction helpful
Unplugged trash compactor and removed from undercounter. Took cover off and removed broken plastic gear. Replaced with new gear and put cover back on

Unit would not operate-off switch broke

  • Customer: Nancy from Rochester NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Husband de-installed the unit and we laid it down on a blanket on the floor. By looking at the diagrams on line we figured out which part we needed. ORDER THIS PART because it is a part that was re-designed to solve the biggest problem with this unit...the foot bar that activates the plunger. In the old design, you had to push up the foot bar at bottom to crush and unlock. Once this redesigned part is installed which requires drilling through the sheet metal (don't worry, they give you a template but hubby did not have the right drill bit), there is a small switch on right of unit under foot pedal which you PUSH with foot NOT PULL UP! Makes the unit much better. Should have been designed like this from the beginning.

Small flat spring flange broke

  • Customer: John from Sugar Grove IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Had to buy the entire switch kit when I only needed a small part. I was told the small part was no longer available

Would not compact

  • Customer: Linda from Rumson NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
It was very easy. I unscrewed the broken acuator and screwed the new one on. It took less than 5 minutes. Much better than paying a repairman $150 for a service call. This part actually breaks often so I ordered 3 or the future.

broken gear

  • Customer: Francine from bowie MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 3 of 4 people found this instruction helpful
Unscrew the bottom, pull out the chain, replace the gear.

Foot actuator broken off at the bend.

  • Customer: Michael from Fresno CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Reattach new actuator using 2 phillips. Very elementary. The difficulty was finding the actual replacement part. Partselect.com made it simple, and my wife now thinks I am a mechanical genius.

broken switch

  • Customer: William from Wilmington NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
I broke the directional switch trying to replace the power nuts..duh huh... ordered a new switch, took off the front panel ( 4 screws) replaced the switch (2 bolts) be careful not to lose the small threaded plate used instead of nuts to secure the switch.. and now it works like new again....partselect is a great resource for the diyer

Compactor piston stuck in down position and couldn't open!!!

  • Customer: George from Houston TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!

Jammed KitchenAid Trash Compactor.

  • Customer: Jan from Gilroy CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 2 of 3 people found this instruction helpful
With nothing in the KitchenAid Instructions nor anything on the internet… I had to go it alone.
Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.
Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.

I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.

I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!

Off-on switch actuator broken (second time same model)

  • Customer: James from Vancouver WA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Ordered two replacements. Was shipped two redesigned parts (assemblies). Installation required more-or-less complete disassembly of garbage compactor. Unit is under-counter and is heavy and work is all at the bottom of unit. Requires drilling two new holes in metal. Instructions give wrong size drill for screws supplied. Supplied screws are robust stainless sheetmetal screws with tiny number one recessed Phillips heads - nearly impossible to drive through two layers of sheet metal with a little screwdriver. Most non-mechanics would have given up and called a repairman.

ram wouldn't go up or down.

  • Customer: Mona from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 2 of 3 people found this instruction helpful
pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.

Plastic Drive gear broke

  • Customer: Terry from Spring TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 2 of 3 people found this instruction helpful
The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.
All Instructions for the KUCS02FRPA0
16-30 of 117