Models > KUCC151JBL0 > Instructions

KUCC151JBL0 KitchenAid Trash Compactor - Instructions

All installation instructions for KUCC151JBL0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the trash compactor repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUCC151JBL0
31-45 of 83
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Wouldn't come back up after compacting

  • Customer: mark from st george UT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 4 people found this instruction helpful
replaced switch and fixed the problem. Still had one more problem after that though, but got that figured out and fixed that to.

Directional switch on a Jenn Aire trash compactor

  • Customer: Danny from Spring Branch TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 2 of 4 people found this instruction helpful
Removed two screws on the front panel cover and lifted off the cover , removed two small screws on the switch bracket, you need a short nut driver, removed the spade clipped wires from the old switch and replaced them on the new part and thats all there was to it.

Plastic Drive gear broke

  • Customer: Terry from Spring TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 2 of 4 people found this instruction helpful
The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.

Compactor would not open. Ram was down

  • Customer: James from Flagstaff AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.

Toe guard was broken, foot pedal was discolored.

  • Customer: Michael from Ashfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 5 people found this instruction helpful
Replaced both, results like new.

motor gear broken

  • Customer: Clem from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

compactor wouldn't shut off

  • Customer: Ray from Dallas GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
changed out the switch and that fixed the problem

Pushed button, made a buzzing noise, nothing happened.

  • Customer: Adrien from East Freetown MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 5 people found this instruction helpful
Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the drive gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 5 of 15 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

unit was missing parts

  • Customer: Richard from glendale AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Installed new parts. Worked fine.

Smelly kitchen

  • Customer: Saralyn from Dahlonega GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Removed the old filter and screen and replaced with the new!

PLASTIC GEAR WHEEL BROKE

  • Customer: Reagan from Glenshaw PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 1 of 3 people found this instruction helpful
Emptied all garbage!
Laid machine on its side.
Removed cover.
Removed left over gear parts by removing pin.
Loosened chain by removing two top left corner screws.
Place new PLASTIC gear in position with chain.
Returned screws to top left corners.
Returned pin to gears.
Make sure chain is taught.
Replace cover.
Lift back up from its side.
Test.

lost cover (went into trash)

  • Customer: Jacek M from Bedford TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
replaced

Broken Drive Gear

  • Customer: Michael from Painted Post NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 4 people found this instruction helpful
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

Ram quit moving

  • Customer: Hal from Granada Hills CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Removed bottom and replaced gears
All Instructions for the KUCC151JBL0
31-45 of 83