Models > KTRS25QAWH11

KTRS25QAWH11 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KTRS25QAWH11

If you know the refrigerator repair part you need, you can browse the list of all parts on the KTRS25QAWH11, or you can search by name or part description. You can also find your part by where it is located on the KTRS25QAWH11 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KTRS25QAWH11 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$108.19

Replacement Ice Maker

***NOTE: Ice maker does NOT come with the bail or shut off arms. Must order them separately if required. It does come complete with flat and round plug wiring harness, the mounti...

$72.18

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$23.19

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$54.74

Icemaker and Water Dispenser Dual Inlet Valve

This valve may be a replacement from the original depending upon your model number. It will function the same as the original.

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air ...

$25.79

Bimetal Defrost Thermostat

This clip-on thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$3.76

Shelf Support Stud

Sold individually.

$10.10

Micro Switch

$8.95

Light Bulb - 10W

This ten watt appliance light bulb is used with both washers and dryers. Sold individually.

$3.76

Icemaker Water Fill Tube Kit

This kit comes with a fill tube and a compression nut.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker quit working, I could manually cycle unit but then the water would overflow when unit was re-filling.

  • Customer: Max from Green Castle IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 490 of 497 people found this instruction helpful
I backed out the 2 top screws about a quarter inch and then removed bottem screw with a quater inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection with a small screwdriver. The new Ice Maker was wired correctley for my refrigeator so all I had to do wea reconnect the power connection and... read more

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 313 of 373 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Ice Maker Fill Tube Freezes Up

  • Customer: Joseph from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 170 of 180 people found this instruction helpful
After a bit of troubleshooting it became obvious that the fill tube was freezing shut because the dispenser valve was not fully closing between fills. It was allowing small drops of water to creep into the fill tube where they would freeze as they entered the freezer compartment eventually plugging the tube shut. The fix was to replace the valve which was ... read more