Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KTRS25QABL11

KTRS25QABL11 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KTRS25QABL11

If you know the refrigerator repair part you need, you can browse the list of all parts on the KTRS25QABL11, or you can search by name or part description. You can also find your part by where it is located on the KTRS25QABL11 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KTRS25QABL11 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$120.88

Replacement Ice Maker

The ice maker ensures your refrigerator generates and dispenses ice. There may be an issue with yours if it leaks water, generates too much or too little ice, or dispenses too much...

$65.25

Icemaker Control Assembly

The icemaker control assembly is located in the freezer section of your refrigerator. It is what controls the icemaker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions, such as the heater, the water inlet valve, the cube size, and cube ejection. This replacement includes the control module and the motor, the motor is not sold separately. There are a number of reasons you might need to replace this part: if the motor is faulty, if any of the gears are worn out, or any of the plastic pieces are broken or damaged. If your icemaker is not functioning properly, you should start by testing this module. Before you begin repairing your refrigerator, make sure it is unplugged.

$9.95

Light Bulb - 10W

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

$27.99

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$5.21

Icemaker Water Fill Tube Kit

The icemaker water fill tube provides water to the icemaker so it can produce ice and dispense water. If you notice that your ice maker is not making or dispensing ice, or is leaki...

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant before it enters the evaporator. When your fan or fan motor is not working your refrigerator will not cool properly. This is a 2-Watt, 115 Volt motor that rotates the fan in a counter clockwise direction. This kit includes the hardware needed for installation, and a set of instructions. Before you begin any repair work make sure to unplug your appliance.

$5.27

Shelf Support Stud

Sold individually.

$20.01

Bimetal Defrost Thermostat

This clip-on thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$17.49

Micro Switch

This switch is located inside the dispenser.

$26.40

Shelf Support Stud

This is a 12 piece kit.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker quit working, I could manually cycle unit but then the water would overflow when unit was re-filling.

  • Customer: Max from Green Castle, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 562 of 580 people found this instruction helpful
I backed out the 2 top screws about a quarter inch and then removed bottem screw with a quater inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection with a small screwdriver. The new Ice Maker was wired correctley for my refrigeator so all I had to do wea reconnect the power connection and... read more

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 500 of 588 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Ice Maker Fill Tube Freezes Up

  • Customer: Joseph from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 226 of 244 people found this instruction helpful
After a bit of troubleshooting it became obvious that the fill tube was freezing shut because the dispenser valve was not fully closing between fills. It was allowing small drops of water to creep into the fill tube where they would freeze as they entered the freezer compartment eventually plugging the tube shut. The fix was to replace the valve which was ... read more