Models > KSSS48QDX05

KSSS48QDX05 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KSSS48QDX05

If you know the refrigerator repair part you need, you can browse the list of all parts on the KSSS48QDX05, or you can search by name or part description. You can also find your part by where it is located on the KSSS48QDX05 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KSSS48QDX05 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$103.78

Replacement Ice Maker

***NOTE: Ice maker does NOT come with the bail or shut off arm. Must order them separately if required. It does come complete with flat and round plug wiring harness, the mountin...

$62.73

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$18.26

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$9.04

Light Bulb - 10W

This 10 watt light bulb is used with both washers and dryers. Sold individually.

$12.32

Light Rocker Switch

This light switch is triggered by the door opening and closing.

$12.48

Micro Switch

This switch is located inside the dispenser.

$15.05

Fan Blade

Used with Evaporator Fan Motors.

$15.34

Water Fill Cup and Bearing

$29.85

Icemaker Shut Off Arm

When the icemaker shut off arm is high enough the ice maker will shut off and no more ice will be made until the level of the ice in the bin drops. Also the ice maker can be turned...

$2.71

SCREW

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker quit working, I could manually cycle unit but then the water would overflow when unit was re-filling.

  • Customer: Max from Green Castle, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 538 of 551 people found this instruction helpful
I backed out the 2 top screws about a quarter inch and then removed bottem screw with a quater inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection with a small screwdriver. The new Ice Maker was wired correctley for my refrigeator so all I had to do wea reconnect the power connection and... read more

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 422 of 502 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Plastic bits dispensed from Ice Dispenser in Door

  • Customer: john from seaford, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 159 of 172 people found this instruction helpful
Removed Ice bin from Fridge

Removed all bolts on bin with nut driver...about six

Removed housing...be careful with spring on crusher/cube control rod

Removed C clamp on end of auger with small slotted screw driver and needle nose pliers.

Removed plastic nut on end of auger shaft

Removed Ice crusher jaws ... read more