Models > KSSC42QMS01

KSSC42QMS01 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KSSC42QMS01

If you know the refrigerator repair part you need, you can browse the list of all parts on the KSSC42QMS01, or you can search by name or part description. You can also find your part by where it is located on the KSSC42QMS01 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KSSC42QMS01 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$2.52

Light Bulb - 40W

Sold individually.

$83.96

Electronic Control Boards - Emitter and Receiver

This set of two electronic control boards contains both the emitter and the receiver. These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker when to refill with water.

$8.76

Control Bracket

This bracket holds the micro switches and the light in the freezer dispenser section.

$72.18

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$9.60

Ice Guide

This ice guide is located in the freezer door.

$49.60

Ice Door Kit

This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.

$10.59

Micro Switch

$8.95

Light Bulb - 10W

This ten watt appliance light bulb is used with both washers and dryers. Sold individually.

$44.50

Water Filter

This filter comes with cyst remover and fits refrigerators with a water filter located in the base grill below the door. It is recommended to replace the filter every 400 gallons ...

$13.66

Ice Bin Coupling

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 299 of 358 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

front door ice wouldn't work and air going into freezer

  • Customer: BILL from BATESVILLE MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 195 of 243 people found this instruction helpful
THANKS TO THE PICTORIAL DIAGRAM, I WAS ABLE TO ORDER CORRECT PARTS. IT WAS JUST A MATTER OF REMOVAL OF BROKEN PARTS AND REPLACING THEM. ICE MAKER NOW WORKING AND AIR IS NO LONGER GETTING INTO FREEZER WHICH WAS FREEZING UP ICE MAKER. THANKS FOR TIMELY DELIVERY, NOW I AM ABLE TO USE ICE DISPENSER, WHICH I HAVEN'T USED FOR LONG TIME. THANKS read more

Ice Maker would not stop making ice.

  • Customer: Vince from El Cajon CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 113 of 124 people found this instruction helpful
First, I tested the ice maker "switch" that actually just covers the beam that regulates the ice maker. In the "off" position, it still made ice. Then, I removed the three screws on the cover over the transmitter and disconnected the circuit board at the wire connector. It stopped. After ordering and receiving the new transmitter and receiver boards, I repla... read more