Models > KSRS25IKSS01 > Instructions

KSRS25IKSS01 KitchenAid Refrigerator - Instructions

All installation instructions for KSRS25IKSS01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSRS25IKSS01
1,156-1,170 of 1,230
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker not working

  • Customer: Gary from Plymouth MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the part recommended by your site, followed the instructions of the associated video and new ice is piling up right now. My only concern was no action for a time right after the install. Turns out the temperature of the freezer must drop back down to ?? before the ice maker starts to work. I was thinking maybe the electrical connection was not good. I choose to wait a night and see if change would occur. Freezer cooled down and ice maker started.

Gary

My ice maker was not making ice

  • Customer: Alfred from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Based on research done on your site, I concluded that my problems was the icemaker control. The video showed me exactly what to do. During removal, I dropped the unit and broke the water fill cup. Ordered the control unit (as well as a replacement for the broken cup). Installed in about ten minutes. You really can't mess up. It only goes in one way! The next day, bucket was full of ice. Thanks for all the help. I figured I saved $200.00 on the cost of a technician call.

Ice maker stopped making ice

  • Customer: Mark from Coraopolis PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the simple steps in the awesome repair video!

Water overflowed icemaker

  • Customer: Stanley from Sharpsburg GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
My first try was to replace the water inlet valve. New valve was a good bit different than the original but not too hard to figure out. The main water inlet is on the inside rather than the outside. Flex hose and a stick in connector were included and I was able to work through that. But, when I turned it on the water still over flowed. The only thing left was the Ice maker. I ordered a new one. It came broken into several pieces. I ordered another, it arrived overnight with expediated shipping. install took maybe 15 minutes. problem solved. The company refunded me the full charge for the damaged ice maker and most of the charge for expediated shipping on the replacement. I'm happy and my wifes very happy.

No water in icemaker

  • Customer: EDWARD from GARDNERS PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
After figuring it out, Some changes had to be made, but everything went smoothly

water leak under refigerator

  • Customer: Ronald from Taylor TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My wife could have made the repair, I got on line, typed the problem in and PartSelect came up. The drawings were there as well as instructions. The part came, again with instructions and it took about 20 min. Good job guys.

ice maker not working

  • Customer: William from East Canton OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Shut off water & electric.Remove 2 screws,cut water lines,unplug electric plug. Install electric plug,push water lines in.reinstall screws,hook up water line & plug in ref.Turn water on, ck for leaks.

Water was dripping from the water dispenser at the front of the refrigerator.

  • Customer: Rick from Garland TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I pulled the refrigerator away from the wall, unplugged the electrical cord, and turned off the water going to the refrigerator. I then removed the cover on the bottom rear of the refrigerator by removing 7 or 8 small screws. Luckily the new and old valves were exactly the same except for some color coding. There were 2 screws to remove that attached the valve to the body of the fridge. There were 3 plastic tubes that connected to the valve and 2 wiring harnesses that plugged in. Before removing them, make sure to note which tubes and wires went where. The 3 tubes on the old valve were the push in type, just like the new one. I could not pull 2 of them out like the instructions said. I had to pry them out with a screw driver. In doing so I warped about 1 inch on the end of each tube which I then cut off with a razor blade. The electrical connections pulled out easily. I then pushed each tube back into the new valve which was very easy and pushed the electrical connections in. I attached the valve to the fridge with the 2 screws, turned the water on, plugged in the electrical cord, and checked for leaks. I put the back cover on and was back in business. It took me about 40 minutes but when I was younger could have done in in half the time.

Ice Maker Stopped Making Ice

  • Customer: Greg from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
When the Ice Maker stopped, I called a repair guy. He wanted almost $500.00 to do the job. I thanked him and paid the $75.00 fee for coming out and got on PartSelect.com to look at what he said was wrong. I ordered the parts -- they came amazingly quickly -- and looked at the videos. The hardest part was that the water valve was a complete replacement and it took a little while to figure out the changes (the old one had nuts and threads; it was completely different). In fact I almost sent it back -- it looked like the wrong part. Once I got going (after chatting with Janet in customer service -- she was awesome!), it took just about two hours to do the whole job. It works great now. My wife even thanked me -- that rarely happens!

Water inlet valve leaked

  • Customer: mark from newton TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Super simple repair, as it takes only a direct replacement of the valve. Removing and replacong the sdrews on the access cover took the majority of the repair time. Two screws retain the valve, and two electrical connections are very simple and easily reached. I would recoment using good sharp side cutters instaed of a knife to cut the three water lines.

My water dispenser quit on the door.

  • Customer: Jeff from GALLATIN TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I knew my ice maker was still working and I could hear that the switch on my water was still making the usual noise when tripped, so I knew that it had to be the inlet valve. I googled some videos and luckily found PartSelect.com. I used there diagnostics, looking at the percentages of other parts used to fix like problems. The part install was very easy as all I had to do was turn off the water and unplug the frig, remove the part, cut the input line and both output lines. Then slide those into the new part, with quick connects you just slide them in, the old part had compression fittings. Reattach the new part turn on the water, plug it back up, watch for leaks, your done..pretty sweet.

Ice make isn't filling due to frozen/plugged water line

  • Customer: Matthew from Yucaipa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pull out the refridgerator from the wall. Unplug the fridge and turn off water supply. Remove the cardboard cover from the bottom of the back side of the fridge. The valve assembly is on the bottom right side of the the fridge when looking at the back. Remove the valve assembly. remove the color coded electrical connectors. Push in the quick disconnect fitting on the valves and gently pull the tubes out of each valve, if it won't come out you can cut the lines, just make sure they are nice and clean and straight. The new part was a perfect fit. Push the tubing in to the size matched valve inlets reconnect the electrical connections reattach valve assembly to the fridge, next open the freezer door and lift the ice make door and take you a hair dryer,turn it on and hold it about 1-2 inches away from the rubber hose that is used to fill the ice maker for about 2-3 minutes to remove the ice blockage. Once it is clear, turn on the water check for leaks and verify correct operation of water and ice. Reinstall the card board, push the fridge back into place. and enjoy a cool beverage and pat your self on the back cause you just fixed your ice maker!

Cold water and ice maker not working.

  • Customer: Steven from Cary NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions in the package, after having viewed the video (from PartSelect, but you have to go to youtube for it.) Replacing the valve got the cold water flowing but there still is no water going to the ice maker.

Continuous water filling Ice maker

  • Customer: David from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First Shut off Water supply from wall/valve. Turned off Ice maker switch interior freezer compartment. Removed power cord from wall plug, important for safety due to close proximity of cooling fan to valve, and resets electrical cycle to new valve to start water flow to ice maker once replaced. Removed lower back cardboard access to frig with nut driver, cleaned all (dust-bunnies)from coils, drip pan and all areas under frig with shop vac. Remove 2 screws (same size nut as cardboard back) to remove valve bracket from mount. This model frig had push release connectors so was even easier than expected, push collars up and pull out tubing, (residual water came out so have towel handy) had new valve positioned exactly how would reinstall so just pushed water line into new valve connector, then repeated process for all 3 water lines. Last unplugged electrical connectors and plugged into new valve in same position. Reattached new valve to mount w/2 screws, turned on water supply to check connections for leaks. (Finding none) Plugged electrical cord back into wall, used water pitcher to cycle water thru door water dispenser, waited for first cycle of water to fill ice maker. So easy and quick. Thank you to previous people who gave directions, and Partselect for easy diagrams, ordering, and shipping quickly.

Missing kick plate after a move.

  • Customer: William from Decatur GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Located part on your easy to use and understand site.Ordered one day and received the next (less than 24 hours). Easy to install. Very pleased with this seller...A+.
All Instructions for the KSRS25IKSS01
1,156-1,170 of 1,230