Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSRP25FNSS00 > Instructions

KSRP25FNSS00 KitchenAid Refrigerator - Instructions

All installation instructions for KSRP25FNSS00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSRP25FNSS00
1,141-1,155 of 1,291
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Chute Freezing Up

  • Customer: Douglas from Raymore, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removal of escutcheon was easy. Replacing icedoor was fairly easy, working with wires in the way was a little distracting but simple. Be careful with microswitches and locating pins. Two of mine broke, had to replace bracket. Simple job again. Everything working fine now. No ice jam in chute. Using needlenose pliers to remove/insert pin is the best and easiest option.

Ice door assembly broken, freezing up ice maker

  • Customer: Sandra from Burlington, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

Refrigerator stopped working completely.

  • Customer: Lyudmila from Nampa, ID
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just replaced the old Push-On Start Relay and it started to work again.

Both sides stopped getting cold

  • Customer: Lynda from Gary, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

refrigerator runs great for 4or5 days then shts down youcan turn the thermostst down and back up or unplug it for a few seconds and it starts up again most of the time.

  • Customer: Darrell from Smithfield, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the relay started right up did fine for about 4 days. Came home from work I had lost everything in the freezer again.turned down the thermostat and back up and it started right up. 5 days later same thing again.

Noticed fridge was not working; compressor would turn on for 10 seconds then shut off

  • Customer: Sean from Savannah, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced broken fridge with a spare fridge; mean while I went online and did research and came across "Parts Select" which was extremely helpful with similiar situation and helpful guidance. $80 and fridge is as good as new.Thank you.

Heard Ticking every minute - Fridge/Freezer not Cold

  • Customer: Chris from Bellingham, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the start relay in about 5 minutes and plugged the fridge in and it started working. Easy repair to get fridge working again.

stopped chilling

  • Customer: Dave from Harrisville, UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did a Google Search for a 1998 Whirlpool ED22RF, looked for trouble Isolation procedures. Don't remember the web sites but two parts were mentioned namely the timer and the thermal relay. After making sure it was unplugged I removed the back lower insulation panel, removed the red wire from the relay located on the left side of the condenser and unplugged the relay. I examined it for physical damage before checking with an ohmmeter and found the thermal relay sounded like it was full of sand when I shook it. So we found PartSelect and searched for the thermal relay and found an exact picture with the part number and ordered the part. We received the $30 part 5 days later. Only took 15 minutes and two tools to install. Thank you for saving us a few hundred dollars.

Warm freezer and fridge compressor clicking on and off

  • Customer: Christopher from Yorkville, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove rear panel with 1/4 nut driver. Pop plastic cover on compressor. Pry off relay and two wires and reinstall. Nice and easy and back to full function :)

freezer not cold /frige not cold

  • Customer: david from germanton, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
un plug first then locate part to replace.lower left corner facing the back . snap off cover on the compressor unplug capacitor install new one.left of capicitor remove the screw on relay install new one.done

Refigerator suddenly started to trip the breaker.

  • Customer: Arturo from Houston, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged refrigerator and removed back cover to expose the compressor and timer/relay assembly. I removed a retainer clip with needle nose pliers, unplugged and removed harness to relay followed by removing the timer/relay assembly together from the compressor. I used the screw driver to pry off very gently. Once removed, the new timer/relay was installed followed by the harness, retainer clip and back cover. The refrigerator was plugged in and my Gladiator man cave fridge was brought back to life.

Refrigerator not cold, Freezer not freezing; running for about 5-10 seconds, then shutting off.

  • Customer: Vicki from Callahan, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video instruction. Looked at online diagram. Removed back cover. Replaced two parts purchased from Partselect.com. Great website, fast service, excellent price! Almost purchased a new refrigerator, but decided to try this first! Happily....working perfectly and spent less than $100 (and saved $1,500 by not purchasing a new refrigerator)!

Whirlpool Refrigerator not cooling

  • Customer: Glenn from Clinton Township, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Besides the refrigerator not cooling, there was a click-buzz-click noise occurring at the rear of the refrigerator every 5-10 minutes. I started by looking up the issue online, I determined the issue was either the compressor or the starter device. I ended up ordering the replcement starter device from partselect.com. The replacement was very easy. All I had to do was pull off the rear cardboard panel, unplug the wire bundle to the starter device, and pull out the starter device.

Would not cool or freeze

  • Customer: Mark from Kingwood, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I did exactly as the man on the video showed me to do. However, I was not sure what part was broke so I replace them both. Under $100 and my problem was fixed. This place had great shipping too: 2 days. They will be my first choice next time I have a problem. Oh and our local repair company would have been $125 for just a service call and they could get to it in a week.

Stopped cooling and freezing

  • Customer: Steve from weatherford, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
No prior experience in appliance repair. The majority of time was used in researching the problem and how to fix it. The Parts-Select website and the comments of prior customers made it easy to diagnose and repair. Unplugged the unit, took off the cardboard back cover, located the start device, using website comments and information pried it off, placed the new one, put cover back on, plugged in. By morning back to 40 degrees. Took apart the old one out of curiosity and it was completely burned-up on the inside.
All Instructions for the KSRP25FNSS00
1,141-1,155 of 1,291