Models > KSRG25FKSS16 > Instructions

KSRG25FKSS16 KitchenAid Refrigerator - Instructions

All installation instructions for KSRG25FKSS16 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSRG25FKSS16
76-90 of 1,324
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water filter end broke off so I could not get out of housing.

  • Customer: William from Waxhaw NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 15 of 20 people found this instruction helpful
Removed 2 screws holding housing to frame. Pulled housing out 10 inches. Removed water lines. Attached water lines to new housing. Pushed back into place. Secured to frame with 2 screws. Put in new filter. DONE!

Fridge and Freezer were not cooling- notices compressor would "click" off after 10 seconds

  • Customer: Scott from Cypress TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 17 people found this instruction helpful
After repairing a similar refrigerator's ice maker a few years ago, I thought I'd try it again. After some brief research online the compressor tested ok. I ordered the start relay and run capacitor and cleaned the coils. The parts arrived promptly and I installed them without a hitch. The fridge has been working great.

Water leaking from inflow water tube at the water filter housing.

  • Customer: Brian from North Augusta SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 14 of 17 people found this instruction helpful
The CAUSE of the LEAK were the O-rings on the water filter itself. My son followed others suggestions on how to detach the water hose from the filter housing, advise was helpful. After replacing the water filter housing, helpful, and inflow water tube the leak was still there. So my son then inspected the water filter and replaced. Water filter light was still green so we did not think it needed attention.

ice maker did not make ice

  • Customer: DAVID from TINLEY PARK IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 16 of 24 people found this instruction helpful
The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

water dispenser not working

  • Customer: Teddie from Sherman Oaks CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 17 of 25 people found this instruction helpful
Remove side handle from the freezer door ...pop out the black panel from the ice/water dispenser... you need to bend it a little bit to remove... un snap the electrical connections ...the plastic connectors, not from the fridge or the back of the panel,there are plastic connectors (white) in the middle between the fridge & the plastic outside panel.I needed a thin knife to lift the connector snaps to pull the pieces apart. It's not a bad idea to note how they match up so you can put it back properly. unscrew the white panel. There are two screws remove panel.I had to cut the micro switch out of the old style panel. the new panel is much more precise. By the way, if you are replacing the micro switch, it's a good thing to know, there are two. One is for the ice maker, the other is for the water dispenser. You might as well replace both at the same time even if one is working it will save you having to do this again anytime soon.Snap the micro chip into place & thread the wires back through the control panel screw the panel back into the door snap the wires togeather. now test the water dispenser just to be sure. Now arm wrestle the panel back in to the tracks. This is the hardest part. Why it doesn't just slide in is beyond me. Must have been designed by a guy!!! It really is easy & it saved me $300.

Auto Defrost Freezer keeps defrosting SIDE BY SIDE KITCHENAID

  • Customer: James from Ringoes NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 18 people found this instruction helpful
DISCONNECT POWER. Removed all shelves/baskets.Popped upper panel off (just clips in) Removed 6 screws in lower back panel ( 3 each side) slid panel in place but down. You can then easily see the defrost thermostat/defrost termination switch. Cut the wire connectors (pink n brown wire) stripped back wire, attached new defrost thermostat. Thermostat clips on. New thermostat ohm's at 5.5, old one was "open". Slid cover back up meeting the upper cover grooves. Screwed lower panel in. Put shelves etc back in. Plugged in. Turns on, put a bottle of water in freezer. Checked a while later, frozen. has been frozen for a week.
-James

Water dispenser hose tip broken.

  • Customer: Sean from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 14 of 18 people found this instruction helpful
The part to fix this was a $50.00 part.
I purchased this Bracket Dispenser for $6.00 and it fit on My fridge perfectly. I just used the screw hole that was a little higher on the water dispenser. Simply cut off the broken end / or Buy a new Hose (Cost at Lowes about $6.00) guide hose along the bracket and use a socken set to reinstall the screw. Water is not squirting on people any more.

One finger of the spring steel peice that holds the ice maker and water dispenser levers out broke.

  • Customer: Ron from Newton IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 15 of 22 people found this instruction helpful
I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix.
I found you by googling appliance repair parts, and found your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron

Frige Door Wouldn't Stay Closed, Would open when freezer door was closed.

  • Customer: Michael from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 12 of 13 people found this instruction helpful
Parts arrived at 2:30PM.

Read instructions, gathered tools, and went to work. I'd already watched an online video at your site on how to do the repair.

Removed the hinge cover covering the hinge top by using a nut driver to remove the single screw holding it in place. (The video described an older frige and it did not have a screw. I figured that out when I finally went and got a ladder. I had tried to pop it out like the video shows.) There are three screws holding the hinge top in place. I tried using the nut driver to remove the screws but they were pretty firmly in place. I resorted to using my ratchet wrench and that made it easy. (Keep track of your screws, one of mine rolled under a cereal box on top of the frige and I thought I would never find it.)

I had emptied out all the items on the door of the frige, removing the shelves. It was easy to lift the door off of the bottom hinge and lay it on its side against the ladder. At this point I had my son hold the door steady (its kind of unwieldy and 'slippery' when you are trying to remove a screw from the bottom of the door.)

I removed the screw that held the plastic Door Closer, Upper Cam using the nut driver. I used a straight bladed screw driver to pry the old part out of the door (it has an insert for the hinge pin and it had been in place a long time). I also cleaned off the bottom of the frige door (you would be surprised what gets stuck on there - obviously someone spilled oranged juice on the floor and it splashed up on the bottom of the door). The old part had a lot of particle dust that came off it when I removed it. The new part popped right into place and I screwed it back in. The video shows that the repairman had to use a drill and tap set to rethread a larger hole but I just put the old screw back and it held fine. The video also showed the repairman adjusting the Door Stop Bracket but I didn't have to do that, the new cam installation wasn't impeded by the bracket.

I moved to the frige cabinet (again, good to have a second pair of hands to keep track of the door and not let it get damaged while I turned my attention to the Door Closer, Lower Cam. I used the nut driver to remove the screw holdin it to the hinge bottom. It came off easily (it practically fell apart and turned to dust). I placed the new cam and screwed it in using the old screw. No problem.

You could put the door back on with one person but it helps to have two. One to manhandle the door and the other to place it on the lower hinge post.

I put the upper hinge back on and put in the three screws but I left them lose so that I could adjust the door. When I tighted the single screw closest to the door after positioning the door, we tested how it opened and it was hitting the side of the interior cabinet when it closed - you could feel it dragging and it made a clunk/swoosh sound. We readjusted the door using the outside upper corner as a guide and retightened the screw. This time there was no problem. We tighted the other two screws using the ratchet wrench and then put the plastic hinge cover back on with the single screw using the nut driver.

Took us about 25 minutes and made my wife very happy (biggest benefit). The door now 'locks' open and 'locks' closed just like when we bought it and the two doors are aligned (level accross the top) which should have been a dead giveaway that the door closing cams had worn down.

Done by 3:00PM.

Ice maker would not stop making ice (Style 2)

  • Customer: James from Satellite Beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 13 people found this instruction helpful
Taped plastic cover to get it out of the way with duct tape - removed three screws on each side - removed retaining screw for each module - carefully disengaged module using small flat head screw driver being sure to release the plastic retainer and then reverse the process. Be sure new modules snap into place.

Biggest problem was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.

ICEMAKER FAILED AFTER 2 YEARS TOP OF LINE UNIT

  • Customer: JAMES from OCALA FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 14 people found this instruction helpful
REMOVED PLASTIC DOOR OVER ICE MAKER REMOVE 4 SCREWS AND SLIDE UNIT OUT AFTER DISCONECTING PULL APART ELECT. PLUG. POP OFF SIDE GEAR COVER INSTALL ON NEW AND SLIDE IN, RECONNECTING ELECTRIC PLUG AS YOU GO.

ice dispenser broken

  • Customer: sandra from mechanicsville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 17 people found this instruction helpful
ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,

Ice door holder arm broken

  • Customer: Joseph S from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 12 of 14 people found this instruction helpful
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Broken light switch

  • Customer: Randy from Hays KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 16 of 26 people found this instruction helpful
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'

Refrigerator door failing to close without being pushed shut

  • Customer: Kenneth from Greeley CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 11 of 12 people found this instruction helpful
Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.
All Instructions for the KSRG25FKSS16
76-90 of 1,324