KSRG25FKSS15 KitchenAid Refrigerator - Instructions

I unscrewed the (3) screws on the bottom of the ice maker & the (1) screw on the electrical cover plate. I unplugged the ice maker & completely removed it from the freezer. Make sure to pay attention to the locking tabs or your maker will not come out. I took the bottom plate off the old ice maker & attached it to the new one, slid it in & re-plugged it. Tighten all screws back where they are to go & now I have ice. It was a breeze to do this job. Part was completely as described.

removed front trim, removed plastic bracket, removed broken ice guide, installed new ice guide, installed removed items in reverse order, finished.

removed the 3 screws from the receiver first, on hinge side with the flap The toughest part was twisting my arm around and upside down to plug the new board into the wire harness since it had very little slack and the wires were stiff from cold, the emitter on the opposite side was as easy, care needed to be taken with the upper screw partially hidden behind ice maker itself but it was an easy removal. Again, short wires and stiff from cold make alignment of the plug to the board just bit awkward to ensure it was seated properly. 15 mins later I heard the first emptying of the ice maker

Remove 3 screws on the emitter and 3 screws on the receiver. Removed the plugs and reinstalled the parts. Very simple and easy. Ice is flowing again.

Researched in "ehow" the procedure. Looked relatively simple so I ordered the part. When it arrived, emptied the frig, pulled it out, thawed out the auto ice maker with a hair dryer. I then examined the old part and compared it to the new part. They were close. Old part had a rivet attaching it to another bracket which had a primary valve that led to the filter cartridge housing. I had to drill out the rivet to seperate the mounting brackets. The electrical connectors were rear facing on the old unit and front facing on the new unit. Not a big problem, just concerned that the solenoid leads might be polarity specific. I called my brother who works on restaurant equipment and he said that as long as the long were the same color, polarity was not an issue. He was right. The second concern I had was that the plastic line from the primary input valve was a stiffer gray plastic line with a rib molded on the ended to secure a metal compression nut. I wondered again if that would cause a problem with the new pressure connector. It did not. Just cut off the rid and slide it in. Frig is working great, dispensing water and ice like it was new. Bought the frig for $1,000 13 years ago, now sells for $2,500. Save a ton of money by buying the part and doing it myself. Thanks.

Just remove old one which was really easy since it was practically falling off and replace with new one. It is a bit tricky because you are afraid of breaking the new one. Watch the video and you will be more confident. I was REALLY impressed with the shipping. I ordered on Monday afternoon and when I returned home Tuesday afternoon it was waiting for me on my porch , and this was the week between Christmas and New Year when everyone was fussing about not receiving packages. NOT ME!

We replaced the ice maker with the help of the video, it was very helpful and it is working fine, thank you very much.

After viewing the very clear video. Remove the ice maker door by first lifting the door and pressing in on the hinges. Remove the screw in the back lower right of ice maker with a one quarter inch nut driver and lift out the cover to expose the wiring harness. Pull the ice maker unit forward and out and reach behind it to pull out the wiring harness plug. The plug only comes out if you depress the small "push clip" in the center of the harness plug. Turn the old ice maker unit upside down and remove the three screws again with the one quarter inch nut driver to lift off the plastic cover. The wiring harness plug need to be pushed through the plastic housing to remove the plastic cover completely. Reinstall the plastic cover on the new ice maker. Reverse the procedure and install the new ice maker. This is really a simple repair if you watch the video.

Did exactly what the video showed . First I went through the test procedure to conferm my boards were bad . But ice maker didn't work after the control boards were replaced. I did some more research to find out what the problem now could be. I discovered where the water goes into the ice tray the line was frozen. Got the hair dryer out and melted the ice that had the water restricted. Been making ice every since. I tell everybody about (part select) web. Sight now

Used hair dryer to melt ice so I could remove old ice maker. Used old icemaker Model #2198597 to order new ice maker. New ice maker water funnel that catches water that goes into the ice mode was higher then the older one. Everything else looked ok. I contacted parts select and was told, if I took the new icemaker apart and it didn't work I could not return it. After three phone calls I was told that I could keep the new ice maker and they would refund my money. So I was left with take the new ice maker apart or cut down the funnel. I cut down the funnel and slid the new ice maker into place. My second choice was to take the new ice maker apart & put on the old funnel. Parts select (Susan) has sent me an email that I would get my money back as the part was not correct. I feel bad about this the way it worked out. It took me about 20 minutes to cut the 1/2 inch off the new funnel.

Followed the instructions in the PartSelect video. It was so easy. Replaced the old ice maker on Monday. Visited a friend on Tuesday. Her Kenmore Frig's ice maker was broken, would not make ice. I told her how easy it was to fix and ordered the part for her today. It should be here by Tuesday and I will install it as soon as it comes in.

I followed the really great repair video on this site. I would not have been able to do it without the video. Thanks very much for the video. Once I had the front panel off, it was relatively easy. Definitely would buy here again and attempt repairs myself. Very good experience! Very happy.

removed ice maker took motor assembly off the end of ice maker, and installed the new part. this was pretty easy because I have taken it apart before. But this is not a hard job for a novice.

When very smoothly, as the video outlined the procedure.

was really ease remove three scwes fron back panel plus two more screws from the water valve