Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSRG25FKSS04

KSRG25FKSS04 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KSRG25FKSS04

If you know the refrigerator repair part you need, you can browse the list of all parts on the KSRG25FKSS04, or you can search by name or part description. You can also find your part by where it is located on the KSRG25FKSS04 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KSRG25FKSS04 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$5.48

Lower Door Closing Cam

The lower door closing cam is designed for use with refrigerators. It can be used on either the fresh food side, or the freezer side. It helps raise the door into position so the door can seal properly when closed. It also allows the door to easily swing open and closed. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace a door closing cam. To successfully install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. This replacement part is sold individually.

$70.75

Water Inlet Valve

Note: This valve has been updated by the manufacturer and NO longer includes the removable pre-filter bracket connector. Must be ordered separately part number WPW10445062.

$4.73

Door Cam - Black

The lower door cam is also known as the closing cam or door closer cam and can be found on your refrigerator or freezer door. The purpose of the lower door cam is to lift the door to keep it from closing on the refrigerator/freezer liner. To do this repair you will need a 5/6 nut driver, a 5/16 socket and ratchet. For safety purposes, do not forget to turn off your appliance before making this repair. Note that this piece is black, and as per the manufacturer requires a new screw to mount the door cam which is sold individually.

$70.52

Water Filter

This ice and water filter fits all Whirlpool and KitchenAid refrigerators with a water filter located in the base grill, below the refrigerator door. This part will also fit any Ke...

$13.30

Control Bracket

This is a control bracket for your refrigerator, and may also be known as the dispenser control bracket. The function of this part is to be used as a fastener to hold the micro switches and the light socket in the freezer dispenser section in place. Its measurements are roughly 9 inches long and 5 inches high, and this model comes in white. The tools you will need in order to make this installation include a Phillips screw driver, a quarter-inch nut-driver, and a pair of needle-nose pliers. If your ice dispenser is not working properly, your bracket could be the problem.

$8.84

Ice Guide

This is a refrigerator ice guide that is made entirely of clear plastic. This ice guide is located in the freezer door. Turn your refrigerator ice dispenser off before replacing th...

$23.78

Bi-Metal Defrost Thermostat

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.

$65.25

Icemaker Control Assembly

The icemaker control assembly is located in the freezer section of your refrigerator. It is what controls the icemaker. The control turns the timing cams and the ejector blades. It...

$55.13

Ice Door Kit

In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute to let ice through when it is being dispensed. If you have the following symptoms such as: door sweating, difficulty opening or closing door, frost buildup, warm freezer section, or problems with ice dispensing, then this is a solution. The tools needed for this repair are a putty knife, needle nose pliers, and 1/4 inch nut driver. Wear work gloves to protect your hands when performing this repair.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Front wheel was broken when moving refrigerator

  • Customer: Jeff from Midway, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 502 of 526 people found this instruction helpful
Lifted the front up onto a scrap 2x4 to get it off the ground and it had 1 bolt that you removed to get the old item off and replace with new assymbly and 1 bolt to re attach. This sat broke for over a year becuase I thought it would be alot harder to fix, found the part on parts select ordered it recieved it in approx 2 days and had it fixed in less than 15... read more

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 511 of 599 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Front Door Ice Wouldn't Work And Air Going Into Freezer

  • Customer: BILL from BATESVILLE, MS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 447 of 522 people found this instruction helpful
Thanks to the pictorial diagram, I was able to order correct parts. It was just a matter of removal of broken parts and replacing them. Ice maker now working and air is no longer getting into freezer which was freezing up ice maker. Thanks for timely delivery, now I am able to use ice dispenser, which I haven't used for long time. Thanks read more