KSRA25FKSS00 KitchenAid Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
coupling broke apart
-
Rodney from Troy, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Leaky water dispenser
I followed the video and was done with the replacement in less than 20 minutes. Just make sure after turning the water back on you check for leaks before you move the refrigerator back.
Parts Used:
-
Robert from Doylestown, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
no ice
-
Nancy from Midlothian, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker stopped making ice.
After determining by the flashing light code what the problem was, I ordered the parts. Once the parts arrived, it took 15 minutes to install them by the instructions that came with them and two hours later I was making ice again. Very easy repair and there is a video on the website that shows exactly how to do it.
Parts Used:
-
Walter from Gibsonville, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker went gaflooey
figured it was either the emitter/receiver or the control module.. even tho the online stats said it was probably the control module, i had a gut feeling (along with a volt/ohmeter) that said it was the emitter..... ordered the part.. came in 2 days..... six screws..... BOOM DONE !!fresh ice !!!!!ohhh what afeeling !!! pete s.
Parts Used:
-
peter from summit, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Clicking sound when opening door
Watched the video provided, then followed that procedure. Everything now works fine, no more clicking.
Parts Used:
-
mike from richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
Noisy fan motor
Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!
Parts Used:
-
eBooks4u from Wimberley, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Part Where Ice Maker Arm Fit In Broke Off
Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect
Parts Used:
-
Yvonne from Worthington, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Frig not cooling.
After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.
Parts Used:
-
Adam from Randolph, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Ice Maker would not eject ice from the ice tray.
Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!
Parts Used:
-
Todd from Meridian, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
condenser fan motor making alot of noise, possibly going out.
A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!
Parts Used:
-
rex from folsom, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Compressor fan and motor was load,barring was wobbling .
-
William from Fox lake, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
None
-
John from New York, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice maker stopped making ice
Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.
Parts Used:
-
Richard from Stephens City, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker would not send ice through the dispenser
Opened the freezer door. Removed the ice bin from the freezer compartment. Removed with a nutdriver the two screws holding down the shaft holder (the triangular white plastic piece). Removed the shaft holder and the circular seal underneath. Pulled the hexagonal metal shaft up and out of the dispenser motor. Installed new circular seal and reinstalled the plastic shaft holder, etc..
Parts Used:
-
jonathan from austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!