Models > KSRA25CNSS00 > Instructions

KSRA25CNSS00 KitchenAid Refrigerator - Instructions

All installation instructions for KSRA25CNSS00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSRA25CNSS00
1,216-1,230 of 1,281
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker not making ice

  • Customer: Gerard from Dublin OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I had to make sure the electronic beam was working properly, which it was (steady beam if you press in the side plastic flap. I also had to make sure the water valve for the icemaker was working properly as well, which it was by switching the lead wires on the valve (water dispenser wire to ice maker valve, and hitting water dispenser paddle and hearing water flow to the ice maker). After that, I knew it was the icemaker motor. Removed three screws with a socket, disconnected wire harness (had to use pliers to pull it apart), pulled out entire icemaker unit. Loosened three screws on motor control unit to remove it from icemaker unit, then inserted new motor control unit and re-screwed the 3 screws. Then I pu tthe entire icemaker unit back in the freezer, connected wire harness, re-inserted three screws and was finished. I then waited for one hour, went to check ice maker and I had ice cubes forming in the tray.

was not making ice

  • Customer: Ricky from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Thanks to this site, it told me what was wrong, what to order and how to repair it.

Icemaker was not making ice

  • Customer: SHARON from Post Falls ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The comments from PartSelect were 50/50 that it would be the motor on the icemaker. We bought the motor which came 4 days leter and followed the installation instructions in the video. We started getting ice about 2 hours after the installation!

Would not make Ice

  • Customer: Len from Apple Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn the unit OFF - Removed one hex head screw on the bottom of the ice maker, removed the cable cover and unplugged. Removed front cover & Slide the icemaker out. Removed control cover and removed the three phillips head screws to the controller. Put the new controller back on with the three phillips head screws, pushed the cover back over the controller. Plugged the unit back in, then slide it back in the tracks, put the cable cover back on and installed the hex head screw, popped the front cover back on and turned the unit ON - DONE!

Ice Maker Stopped Working

  • Customer: Susan from Flemington NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
My dad and I worked together. The video helped but it was a little more complicated. If you can't find the water supply, remove the filter and water should stop, that's what we did. We had to remove the freezer door for access to the ice maker. It was tricky taking the icemaker off and getting it back on. Replacing the motor was easy, just as shown in the video. Just like others have said, within an hour of the repair the ice starting coming!

no ice, no water dispense into icemaker tray

  • Customer: nguyen from albuquerque NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My name is Tuan Nguyen. I have no ice and no water dispense into icemaker tray. I replace the the icemaker control and motor assembly. I unscrew a screw underneath the icemaker unit and disconnect the wire clip and pull out the icemaker assembly. I remover 3 screw from the motor assembly unit and replaced it with the new motor assembly. and installed the unit back in the compartment. It took about twenty min. It make me look good, that my wife knows i can fixed the problem without calling the repair men.

ICE WOOD FREEZEE UP NOT DROP OUT

  • Customer: danny from visalia CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
put part on /did not see warter come at first had to go a cycal then ice again thanks alot, danny repair guy whanted 46$ to look at part.GOOD JOB.

ICEE MAKER STOPPED MAKING ICE

  • Customer: Geula from Morganville NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My Ice maker has been broken since August 2011. I called my son in law, which is very handy, he looked at the broken ice maker, said he had no clue how to fix it, since its computerized. Searched the internet, found Part select website, watched videos, read customers feed back, based on information provided, ordered icemaker Control and Motor Assembly (less than $60.00), called my Son in Law, in less than 10 Minutes, part was installed. The next morning the Ice bin was full. I am so greatful for your Website, and my wonderful son in law.

Ice maker stopped making ice

  • Customer: Vonnette from Bixby OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unscrewed bolts pulled out motor,unhooked motor,replaced with new motor,put back in and replaced screws..fairly easy..then we had ice that evening!

Not making ice

  • Customer: Thomas from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Video instructions walked me right thru it had no problems.

ice maker stop working

  • Customer: thuy from Houston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
turn power off, take the little cover on front of ice maker off so you can pull ice maker box out easier, unplug the easy connector ,after this take square cover off you'll see control motor take 3 screws off pull control motor out change new one in ,put them back together.turn power back on .then now Ice Maker will make some after 2 hours .You will SMILING then say ,Oh Yeah. QT good luck to everyone

Broken icemaker during summer in Texas.

  • Customer: Colin from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The online video shortened the learning curve, and the cut the repair time in half.

No water coming into ice maker

  • Customer: Ricardo from Hialeah Gardens FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

ice maker wasn't

  • Customer: Mona from The Sea Ranch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

timer motor died

  • Customer: Paul from Moline IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas
All Instructions for the KSRA25CNSS00
1,216-1,230 of 1,281