Models > KSRA25CNSS00

KSRA25CNSS00 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KSRA25CNSS00

If you know the refrigerator repair part you need, you can browse the list of all parts on the KSRA25CNSS00, or you can search by name or part description. You can also find your part by where it is located on the KSRA25CNSS00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KSRA25CNSS00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$44.50

Ice and Water Filter

This filter is mounted in the bottom grille. Sold individually.

$3.76

Lower Door Closing Cam

This door closing cam is located on the bottom of the fridge/freezer.

$2.52

Light Bulb - 40W

Sold individually.

$114.64

Ice Maker Assembly - 8 Cube

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

$3.82

Door Cam

Note: As per manufacture a new screw is needed to mount door cam. Sold individually.

$143.96

Electronic Control Boards - Emitter and Receiver

This set of two electronic control boards contains both the emitter and the receiver. These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker when to refill with water.

$71.06

Water Inlet Valve

The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold. Note: This valv...

$72.18

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$8.07

Ice Guide

This ice guide is located in the freezer door.

$49.60

Ice Door Kit

This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Front wheel was broken when moving refrigerator

  • Customer: Jeff from Midway GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 463 of 466 people found this instruction helpful
Lifted the front up onto a scrap 2x4 to get it off the ground and it had 1 bolt that you removed to get the old item off and replace with new assymbly and 1 bolt to re attach. This sat broke for over a year becuase I thought it would be alot harder to fix, found the part on parts select ordered it recieved it in approx 2 days and had it fixed in less than 15... read more

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 327 of 391 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Ice maker stopped functioning

  • Customer: Phil from Auberry CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 252 of 263 people found this instruction helpful
Remove the icemaker service door... gently pry the door pins from the hinge sockets. Remove the 3 screws from the under side of the icemaker with a nut driver (1/4"). Gently remove the icemaker . It's a tight fit between the top of the compartment and the icemaker lower support tray. Next, disconnect the electrical connector at the right side. You're do... read more