KSM90WH KitchenAid Mixer - Instructions

‘Can’t remember well enough to describe accurately. Removed one screw to remove rear cover. Removed two screws to remove bright-metal band - probably not necessary but it did yield a bit more working space. IIRC, three screws and removing wires from spade-connectors was sufficient to remove the speed control plate. Remove one more screw to remove phase control board (probably unnecessary). I took close-up pictures with my iPhone first to assure wires would get replaced on the proper lugs (only to discover the wiring diagram later). Adjusting the control plate to meet the speed criteria in the instructions was very easy. It did serve to remind me that I probably didn’t need either of the new parts; readjusting the old speed control plate would probably have done it. But I appreciate the POM brought on by the new parts.

It’s an incredible pleasure to work on something so well-made as this old Kitchen-Aid mixer. I just enjoyed handling it! Having achieved a proper repair was rather satisfying too. I just loved the entire experience!

Removed back cover, disconnected the 2 push-on connectors, removed ground wire screw. Reversed the process to install new cord.

followed the emailed instructions from your company
worked perfectly
thanks

I decided to update the motor brushes in our KitchenA id mixer even though it operated perfectly for years. After installing the motor brushes, you sent,I plugged the cord attached to the mixer into the outlet. I selected 1 on the speed selector and nothing occurred. The mixer would not operate. I then checked the outlet to insure there was voltage present; there was voltage present. I again plugged the cord of the mixer into the outlet, selected 1, then 5, and finally 10, with no results. The mixer would not operate. Finally, I removed the motor brushes I had received from you and installed the old brushes that were originally in the mixer, plugged it in the outlet, selected 1 and the mixer operated perfectly as it did BEFORE installing the brushes you sent.

just as the you tube instructions said.

We simply replaced the gear with the new one. It was very easy to install.

Tried new brushes but alas it looks like it was a controller. Wife needed it asap so Ii bought her a new one. Service and delivery were quick but couldn't wait for a second part to try and repair it again.

Really no help from Kitchen Aid sources; but phone call to PartSelect solved the problem. Kitchen Aid repair line didn't even know the part #! Thanks to Part/Select, Christmas cookies are being made.

To access the interior of the mixer, I first removed the single screw holding the cup-shaped part at the rear. Then I removed the 4 large screws on the under surface of the mixer head. Next I removed the bright metal ring around the planetary gear area by prying it off. I then pried the dish-shaped part off the shaft using a large-bladed screwdriver. This exposed 5 screws on the circumference of the planetary gear. By removing them, one can pull up the gears and see into the area below. I found the worm gear had fractured. By removing 3 screws at the base I extracted it for closer inspection, checking for any loose pieces. Beware of the jelly-like grease. The replacement part goes into position, and one then follows the steps in reverse.

I removed the decorative band that covers the seam by removing 1 screw. I then removed the top portion of mixer by removing 4 square head screws. You will then see the gear housing in the front of the mixer. Remove the 4 screws holding that on. There are no spring that are going to pop out and you never know where they went, but be careful because there is a lot of grease and a gear that it just laying in there on the right side. You will see the stainless shaft with a couple on gear cogs on it. Remove the retaing spring from the shaft and pull the top gear off, it may be a little snug. You will then see the dowel pin, mine was sheared off but I could see where it was. Be sure to remove the broken pieces. Use the punch to knock out the remaining pin. Replace with new pin making sure it is evenly exposed on both side of the shaft. Replace the top gear, then the retaining spring, the the gear housing cover, then the mixer top cover and finally the decorative band. Be sure to unplug before you start. These mixers are expensive and expensive to have someone fix them. I ordered 2 pins because shipping is a little high and the pin is cheap. I fixed this for $17.00 total and have a spare pin.

After stalling the mixer while mixing dough I found that the motor still functioned but the blade didn't move. I basically took the mixer into my shop along with a digital camera to record any complicated disassembly procedure I might have to deal with for reassembly and proceeded to disassemble the mixer. Once apart, I cleaned the mixer parts, removed the broken worm gear and bracket, and got online for someone that carried the replacement piece. PartSelect sent the replacement within 3 days and now it works great again.

dissassembled mixer and replaced gear

just inserted the new wire whip

Dear Customer Service,

I just would like to express my gratitude for your wonderful service. I received my part for my Kitchen aide mixer on time as promised. The part fit perfectly. Thanks you PartSelect for being there.
What a Great Site!

A Happy Customer!

No nstallation required, simply attach.
Your website was the only one that made sense. I am blind and follow the instructions with a screen reader. I had no difficulty. It was much easier than this questionaire.