Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSCS25INSS01 > Instructions

KSCS25INSS01 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25INSS01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25INSS01
976-990 of 1,079
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

after power outage stopped making ice

  • Customer: steve from carson city, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This is a built-in refer. I just turned of the power by flippig the breaker to the refer in electrical panel. Then I removed the white cover to the ice maker and the metal arm no tools required.Then I removed the 3 screws and removed the motor & control assembly then replaced it with the new one. Easy put 3 screws back in snapped cover back on and reinstalled metal arm flipped breaker back on done 15 minute or less. (note: It's helpfull to use a small mirror to see the back side of control if you don't remove ice maker from refer to reinstall metal arm.)Also in my case everything was working now but it didn't produce ice? I looked in the rear of ice maker where the water supply comes in and it was frozen. (little trough or shute.)I carefully chipped ice out with ice pick came out easy. Started making ice and filled up over night everything working great. Final note: (if water freezes up in shute again it's the water valve that needs replacing. I was told that it means it's leaking.) Hope this is helps.

Ice maker would'nt make ice...

  • Customer: John from austell, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
This fridge is s ultraease 2 its 8 years old. Icemaker would'nt make ice. Its fairly easy all you do is take out the screws i recommend a power drill tho. Pop out the cover put the new motor in. I did'nt hear anyththing or see anything for a hour or two thought it did'nt work. Then i heard a clunk like ice falling into a bin. 3 hours later ice was falling frequently.

The ice maker not working

  • Customer: David from Rockwell, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pull the ice maker out using a nutdriver Pull the use a srew driver to remove the srews did the same to replace it put it back in had ice in 20 min

Icemaker Didn't Work and Leaked Water in Freezer

  • Customer: Cliff from Arden, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After googling for a parts supplier, PartSelect.com came up. The site was well done and had the Parts List conveniently available. I watched the associated video which was the highest quality "how-to" repair video I have seen. As it turns out, though, the icemaker does not have to be removed from the freezer unit. I removed the icemaker's shutoff lever, removed 3 screws, pulled the motor assy off, slid the new motor assy in place and re-installed 3 screws. Reinstalled the shutoff lever per the video and JOB DONE.

Ice maker stopped making ice

  • Customer: Mark from Beaverton, OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Verified that the sensors were working. After removing the Ice maker assembly from the sliding track, I found that the indexed drive wheel on the motor had broken off from the shaft mounting. I ordered the Icemaker control and motor assembly from Partselect and swapped out the bad part. It only has three screws to remove and replace so it's fast and easy to fix.

would not make ice

  • Customer: Tyrone from Doddridge, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I got the new part and unplugged the refrigerator. I removed the wire auto shut-off. I removed the old motor assy. I checked to see if the motor quit running at the same locations as the new one before removing the entire ice maker. Lucky it did, so I installed the new motor assy without having to remove the ice maker. It took 10 minutes at the most.

Plastic peice broke in the icemaker control

  • Customer: Brandon from New Brighton, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unpluged the refrigerator. Removed the cover on the control unit by inserting a screw driver under the metal clips. Removed the three screws frrom the front of the control unit. Pulled toward the back of the refrigerator on the metal loop which turns the icemaker on and off and it came loose where it goes into the control unit. Wiggled the unit and it came free. place the new unit in approximately the right position. Reached into the icemaker and moved the ice eject leavers so the shaft would enter the control unit with the flat side of the ejector in the right position. Gently pushed the control unit into its place and aligned the screw holes. Replaced the three screws. Inserted the wire shut off loop into the hole on the back of the control unit housing. Pluged in the electric. The ice maker worked.

Not making ice.

  • Customer: George from Palm Coast, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions on video on website. Very easy to do. Removed old part, put in new and it took all of 15-20 minutes. Had ice in approximately 1 hour.

Did not make ice

  • Customer: Robert from Jacksonville, AR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched video on changing out the ice maker motor and followed instructions and it was as easy as video demonstrated. Received replacement motor in 3 days. Great service.

Ice Maker would not make ice

  • Customer: Anthony from Clarence Center, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed ice make from freezer. Removed end cap and replaced control and mostor assembly. The associated You Tube video was very helpful.

Ice maker wasn't making ice

  • Customer: Rich from Holly Springs, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled out the icemaker. Switched out the Motor Assembly (so easy) and woke up the next morning with ice. Our ice dispenser wasn't working either. This repair inspired me to take the ice dispenser apart and I found that the lever arm wasn't touching the contact when pressed. We now have ice and a working ice despenser. Oh yeah--my wife was so impressed. The part came in on time and it was very very easy to replace.

Wasn't making ice

  • Customer: Allan from Pasadena, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off the water to the ice maker; disconnected the wiring harness to the ice maker; unscrewed it from the freezer (two screws). Unhooked the ice lever bar, opened up the motor assembly. Switch the motor out (two screws). Installed in reverse order.

Ice maker replacement

  • Customer: john from ellijay, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Extremely simple especially after watching the video. Makes me think about why I did not attempt my own appliance repairs in the past. Big time savings! Thanks. P. S. excellent delivery service from Parts Select.

quit making ice

  • Customer: patrick from escalon, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaceed control motor assembly 3 screws took it off. then turned ice maker shaft by hand to line up key slot on new control unit . slid right together .ice started making within an hour . and the part got to my house the very next day after ordering awesome...

Ice Maker won't make ice

  • Customer: Shawn from Hagerstown, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video so I had an idea of what to do. It was pretty straightforward. Turn off the water, take out the screws, line everything up, replace the part. It went smoothly and the icemaker is working again. :)
All Instructions for the KSCS25INSS01
976-990 of 1,079