Models > KSCS25FKSS02 > Instructions

KSCS25FKSS02 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25FKSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25FKSS02
1,066-1,080 of 1,185
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No water coming into ice maker

  • Customer: Ricardo from Hialeah Gardens FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

stopped producing ice

  • Customer: Walter from Palm Beach Gardens FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

ice maker wasn't

  • Customer: Mona from The Sea Ranch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

would not make ice

  • Customer: Tyrone from Doddridge AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I got the new part and unplugged the refrigerator. I removed the wire auto shut-off. I removed the old motor assy. I checked to see if the motor quit running at the same locations as the new one before removing the entire ice maker. Lucky it did, so I installed the new motor assy without having to remove the ice maker. It took 10 minutes at the most.

Icemaker was not working

  • Customer: CRAIG from PORT ST LUCIE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed three screws, inserted new part, completed in less than 10 minutes and my icemaker works!!!! My icemaker did not work for 2 years and after spending $58, my icemaker was back in action.

Would not make Ice

  • Customer: Brenda from Costa Mesa CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
First of all, I am a female. So anyone can do this.I simple watched your video. Made the repair very simple. I was surprised that it really worked. I couldn't understand that if the door would still eject ice, why it wouldn't make the ice. It's the same motor. Anyway, It worked and I thank you very much. Very satisfied.

Broken switch inside control module.

  • Customer: Mark from Brighton IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
With brief instuctions it was very sraight forward. Three scews hold the motor assembly on. Ordered on a Sunday and the part was here the following Tues. Thanks Partselect

Ice maker replacement

  • Customer: john from ellijay GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Extremely simple especially after watching the video. Makes me think about why I did not attempt my own appliance repairs in the past. Big time savings! Thanks. P. S. excellent delivery service from Parts Select.

quit making ice

  • Customer: patrick from escalon CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaceed control motor assembly 3 screws took it off. then turned ice maker shaft by hand to line up key slot on new control unit . slid right together .ice started making within an hour . and the part got to my house the very next day after ordering awesome...

Ice Maker won't make ice

  • Customer: Shawn from Hagerstown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video so I had an idea of what to do. It was pretty straightforward. Turn off the water, take out the screws, line everything up, replace the part. It went smoothly and the icemaker is working again. :)

Did not make ice

  • Customer: Robert from Jacksonville AR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched video on changing out the ice maker motor and followed instructions and it was as easy as video demonstrated. Received replacement motor in 3 days. Great service.

Ice Maker would not make ice

  • Customer: Anthony from Clarence Center NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed ice make from freezer. Removed end cap and replaced control and mostor assembly. The associated You Tube video was very helpful.

Ice maker stopped working.

  • Customer: Donald from Sault Ste Marie MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I took the ice maker right out

Motor stopped working and was leaking

  • Customer: christine from horsham PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
At first I just ordered a new motor and followed the instructions on the video . The new motor started working overtime but no water was being delivered to the tray . Ordered a new tray and re-installed. Working fine now. At first the ice was sticking, but that seems to have stopped now. It may be better to pull the ice maker out and check to see if there is damage to the tray before ordering. That way it could save the time of not doing things twice.

Icemaker inoperable

  • Customer: Edgar from North Tonawanda NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced Control and Motor on the basis that most respondents found this unit to be at fault when the icemaker failed. Unfortunately, this wasn't the problem. Sudsequently, I replaced the electrionic boards which did fix the system. It would have been helpful (and less expensive) if the PatrsSelect website provided more help with problem diagnosis. Otherwise, the website is great!
All Instructions for the KSCS25FKSS02
1,066-1,080 of 1,185