Models > KSCS25FKSS02 > Instructions

KSCS25FKSS02 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25FKSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25FKSS02
916-930 of 1,185
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker leaking into ice bin

  • Customer: Frank from Cat Spring TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Turned off circuit breaker. That turns off both power and water. No need to move refrigerator. I backed out the 2 top screws about a quarter inch and then removed bottom screw with a quarter inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection. The new Ice Maker was wired correctly for my refrigerator so all I had to do was reconnect the power connection and mount new Ice Maker on the two top screws and install the bottom screw. It took about two hours for the new Ice Maker to start it's cycle but after it did, it worked GREAT. Part Select service was OUTSTANDING, ordered part one day and received it in two days and I live in a very remote location. Recommend PartSelect to everyone.

I quit making ice

  • Customer: Eric from Sheridan WY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Online I learned how to diagnose the problem and order the part I needed. Replacement was simple and now we have ice. It works perfect, no adjustments needed.

Ice maker stopped working

  • Customer: Harry from Placentia CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the video on the web site. Easy squeezy.

NO ICE

  • Customer: andy from ANNANDALE MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
SHOULD HAVE.... Just taken the ice maker out in the first place ....When I saw no ice I assumed the timer was bad...Replaced it..Then when that didn't fix it again ASSUMED that water valve was bad....Replace that also to no avail....FINALLY took out the ice maker and saw that the heater had stopped working cuz there was still ice stuck in it..Replaced ice maker...All good...The water valve I replaced was a good thing cuz you can definatley tell the difference.... ANYWAY...FIXED!

My Ice Maker Stopped Making Ice

  • Customer: David from Roswell GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I replace the Ice Maker unit. Not only was the replacement/repair activity very easy, locating, ordering and receiving the part from PartSelect was priced competitively, very easy, quick and I received the part earler than expected (always a nice thing!).

ice maker leaking

  • Customer: Joni from Saint Charles MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the old one out and put the new one in.

Water leaking from ice maker tray

  • Customer: Steven from Rochester MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After watching the how to video posted on Parts Select I thought this looks very simple. It takes you step by step on how to install the ice maker. It was very easy and the video was right on the mark! Thanks again Parts Select you saved me a bunch of $$$.

none

  • Customer: Gary A. from Gypsum CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Thanks to your video the repair went rather smoothly.

iCE MAKER STOPPED WORKING.

  • Customer: allan from Palm Desert CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
REPLACED WITH THE NEW UNIT, THEN FOUND WATER STILL NOT GOING INTO TRAY, SERVICE TUBE WAS FAULTY, NEW ONE INSTALLED AND UNIT WORKED FINE, ...PROBABLY DID NOT NEED TO REPLACE THE WHOLE UNIT.

Ice Build up in the ice cube storage bin

  • Customer: Carol from Yucaipa CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
If the ice maker mold develops a hole it will leak water causing an ice icicle to form on the bottom. If this is your symptom its time to replace the ice maker. The first step is to shut off water supply and unplug refrigerator. Next loosen the two upper screws and try not to remove them. On the bottom towards the front of the ice maker there is one screw. This is mounting bracket screw, remove it completely. At this point hold the ice maker a push it upwards to remove it from the upper mounting brackets. Once it is free from the mounting brackets you will have access to the wiring harness. The plug clips in place so you will have to spread it while unplugging it. Most likely you will have to remove shut-off arm and may be the heat shield as well from old unit. You may have to tug them some what to remove them from the front of the old ice maker. Suggest wearing work gloves for this step to avoid being cut. Install parts on the new ice maker by snapping them in place. Verify that the new icemaker has the correct wiring harness if so you are all set to install it. Place the new unit in the compartment and plug it in. Make sure it is also lined up in the rear where the water tube is a well. Now line up the upper screws with both support brackets and push down gently to lock them in. Install lower mounting screw. Snug up the upper screws enough so the unit is flush to the freezer wall and feels secure. Turn on water supply and plug in the refrigerator. Your Done And A Hero to your better half.

ice dam at rear of ice maker

  • Customer: William from Bloomingdale MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I reviewed the video and followed the instructions. Simple and straight forward. A mirror helps see the one hidden screw head.

ice maker door failed to close causing frost to form preventing proper operation of icemaker.

  • Customer: Melinda from Owasso OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Found video on YouTube. Ordered part from partselect. Part arrived and viewed video to refresh memory. Our refrig was a little newer than the video but the process ww was the same and quite simple after viewing the video.

Ice dispenser door dislodged/broken-causing ice/frost in freezer

  • Customer: LAWRENCE from Gig Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

Plastic hinge attached to chute door broke

  • Customer: James from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video showing how to disassemble unit and it showed that there was a heat element inside the chute door under the foam seal that needed to be removed and placed in side the new chute door. I spent about 10-15 minutes trying to salvage the element but the adhesive used would not release and the part was rendered unusable. I called the help line and was told that their instructions on that kit said the heating element was no longer required. I finished putting the kit in and the unit works fine

The plastic Ice Handle had broken after years of use

  • Customer: Tom from Hollis NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!
All Instructions for the KSCS25FKSS02
916-930 of 1,185