Models > KSCS25FKSS02 > Instructions

KSCS25FKSS02 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25FKSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25FKSS02
901-915 of 1,189
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker failed tp produce ice

  • Customer: Peter from Punta Gorda, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed three screws. Discount wire harness. Reverse proceedure for installation.

old icemaker went bad the form tray bubbled up and held cubes in place that stripped the drive gears at the motor end

  • Customer: Jon from Barnegat, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the u-tube video first ,Then read instructions that came with new unit ! so darn easy. unplug fridge, remove ice bin, clean and dry bin before putting back in service! stick flashlight in freezer loosen 2 top screws remove 1 bottom screw, unmount unit, unplug wire harness, remove icemaker and put on table, close freezer door !! , Remove sensor arm from old unit in down position and install in new unit. plug in new unit and reattach in freezer. replace ice bin and plug in fridge, that's it!, It took about 2 hours for the icemaker thermostat to say OK lets go had a load of ice in aprox 3 hours from finish. piece of cake. Jon

ice maker did not function

  • Customer: Gary from Garfield, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
watched video, followed the instructions and everything fell into place. since the wiring harness was not removable, I disconnected the harness from the the old unit and hooked it up to the new unit. put every thing back together,plugged in the power cord and turned on the water. water filled the ice maker and ice appeared in about an hour.

ice maker was leaking and not making correctly making ice cubes

  • Customer: Melba from Aberdeen, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ice cubes are now being made properly and there is no more leaking.

Iscles Hanging From Underside Of Icemaker & Frozen "Pudles" In The Ice Bin.

  • Customer: NEAL from boyton beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Previous to installing the new ice maker - I replaced the dual inlet water valve per the instruction video I found @ partselect website. That did not solve the problem <> I also adjusted the timer on the old ice maker down - per another video / which also did not solve the problem. Then I viewed the video on icemaker replacement - ordered the ice maker & 3 days and 15 minutes later <> the problem was fixed ! This web site is "fantastic" ! Thankyou partselect for your assistance ! ! !

Ice maker was leaking

  • Customer: Nick from Duck, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Really couldn't be easier. Loosen 3 screws that are easy to find. Disconnect the quick connect wiring harness. Now you have the old unit out. Take out the wire that tells if there is too much ice from the old unit and put it on the new one ( this was the hardest part of the project) Hook up the new wiring connector and hook it on the screws and tighten it up. Viola, your done. No messing with the water. Took me 5 minutes and I've never done it before.

Ice maker was not making ice.

  • Customer: Edward from San Angelo, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed the example on the video and everything fit in place without any problems. Only issue is that on a double door fridge the freezer is rather narrow so there isn't much room to work making it was a bit difficult to access the mounting screws.

Ice maker leaking

  • Customer: Charles from Hitchcock, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Shut off water to icemaker, unplugged frig, loosened top 2 screws on iccemaker, removed bottom screw, unplugged icemaker and removed from frig. new plug in was the same so didn't need to chan ge it. reversed steps to install, back in businees in less than 15 mins., making ice and no leaks!!!!!!!

my ice maker was leaking into my ice bucket freezing it into a solid chunk

  • Customer: Becky from Perryton, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the installation video and did just like it said. It was pretty easy. My ice maker is working once again, and I'm pretty proud!

failing icemaker

  • Customer: geoffrey from flagler beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

Icemaker had started leaking water into ice bin upon filling.

  • Customer: John from Colombia, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the online video and it looked just too simple.....so when I got the new unit I did not have to even change the wiring harness and I was totally surprised that the change could be so simple and easy! Trick is to follow the video instructions and DO NOT take out the two top screws but just loosen them enough to lift up the old unit and remove it! Cannot believe it could be that simple and easy.

Ice Maker heating element stopped working . Ice was stuck in ice maker.

  • Customer: jeff from Roland, AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Just removed old ice maker which took about 2 minutes. installed new ice maker in about two minutes. Simple and easy install.

Ice maker dripping water creating issues in freezer

  • Customer: Robert from Vienna, WV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Searched internet until I found a company(yours) with the part needed. Could not locate locally refrigerator too old. After finding"Part Select" site I watched the video provided. It was very instructive and helpful. I cancelled calling any repair service and did the repair myself. The part was delivered fast and I had no problems with the repair. Your confirmation e-mail of part being shipped again provided the video for the repair. I only watched again after the repair to check myself, all went well. My Ice maker is working great again and I consider this purchase money well spent. I was considering another refrigerator but will now keep the Kitchen aid longer, Thank you.

Would not make ice cubes.

  • Customer: Yvonne from Kennewick, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The icemaker is in a side by side refrigerator/freezer with an auger driven ice bin dispenser, so space was limited. I first removed the ice bin but I couldn't see the three nuts holding the icemaker in place. I removed the ice bin support bracket (under the icemaker) using a Phillips head screw driver. Now the bottom nut holding the icemaker in place was easily visible and I was able to determine the size of nut driver I needed to completely remove it. Then I felt for the location of the top two nuts, slipped the nut driver on and loosened them. I was able to lift the icemaker off the top two nuts without completely removing them. Using a flat head screw driver, I pushed down the white tab holding the wiring harness connection to the icemaker and removed the harness, freeing the ice maker for complete removal. I did not need to replace the wiring harness, so I simply reversed the whole process to install the new icemaker. I am a 61 year old female with rheumatoid & degenerative arthritis and found this installation really easy, with the one exception of snapping the wiring harness connection into the new icemaker - I didn't have the thumb strength. I had to wait for a relative to come and snap the wiring harness connector into place for me. I also had to use some snips to cut out the plastic tab (scored) for the water feed to the icemaker but was able to complete the entire installation within 30 minutes.

iCEMAKER FAILED TO MAKE ICE.

  • Customer: Charles from Spring, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplug the unit cord, remove 3 screws on the icemaker. Unhook the wiring harness from the refrigerator, remove the unit and reverse the order to install the new unit. Reinstall the on off bail, and the icemaker tray. Make sure that the unit is level after the new installation so that water does not spill out of the icemaker.
All Instructions for the KSCS25FKSS02
901-915 of 1,189