Models > KSCS25FKSS02 > Instructions

KSCS25FKSS02 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25FKSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25FKSS02
886-900 of 1,189
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker not working

  • Customer: Gary from Plymouth MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the part recommended by your site, followed the instructions of the associated video and new ice is piling up right now. My only concern was no action for a time right after the install. Turns out the temperature of the freezer must drop back down to ?? before the ice maker starts to work. I was thinking maybe the electrical connection was not good. I choose to wait a night and see if change would occur. Freezer cooled down and ice maker started.

Gary

stopped producing ice

  • Customer: Walter from Palm Beach Gardens FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

ice door would not seal warm air out & ice maker would freeze up.

  • Customer: Earl S. from Denison TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After reading (Warm air getting into freezer) by David from Chesterfield, MO & (Ice door was broken) by Ray from San Antonio, TX, it was easy to follow their instructions (especially- Patience is a virtue! and go step by step. Thanks to both for their detailed instructions, this retired mechanical engineer was able to 'get it done'. Stan from Denison, TX

couldnt use ice maker dispencer. ice melting and leaking

  • Customer: Kevin from Wyandotte MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

Broken crisper drawer cover, door shelf bin, light lens and cracked shelf studs.

  • Customer: Diane from Issaquah WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Crisper drawer cover, door shelf bin and light lens required no tools. Very easy to simply trade out broken ones for new ones. Cracked shelf studs just required a screw driver - again very easy. Replacing everything took just minutes.

freezer was freezeing up

  • Customer: phillip from palmyra VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

fridge too warm

  • Customer: mike from ROSCOE IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

The refrigerator would not defrost and would freeze up and no longer cool.

  • Customer: Mike from Frankfort IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

freezer forming ice on back panel, fridge nor freezer getting cold

  • Customer: Frank from Alabaster AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

Solid ice on Evaporator coil

  • Customer: PRAKASH from PISCATAWAY NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

Refrigerator was getting warm

  • Customer: Mack from Los Banos CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

Freezer OK. Refrigerator Not Cooling.

  • Customer: Donald from Kissimmee FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed recommendations from others but went with most likely by percentage = Defrost Timer Kit. Did not solve issue. Then went with Bi-Metal Thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part OK. Then I saw on line that I should have listened for Fan operation. I checked and found the fan Motor to be defective. Replaced the motor and Refrigerator worked fine. Both the Motor and Bi-Metal Thermostat were required. Should have checked fan operation first.

refrigerator and freezer would stay frozen.

  • Customer: Jack from Poplarville MS
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

freezer freeze at bottom shelf lot of ice door c annot seal thight .watter leak at bottom of door on kitchen floor my wife stuck tee shirt at bottom of door to prevent watter to flow into living room .we did that for several months we actualy had to defrost several time per week anddug out ice

  • Customer: Hemchand from Queens NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
the bi metal defrost thermostat was the problem when i saw the parts i click on it you will see the diagram of the section where the parts located you will also given a video how to removed and replaced the parts these people make it so good for appliance owner i actually fixed my washing machine was not working i trouble shoot the model and go with the highest percentage parts to fixed the problem with this web i am going to keep my appliance for years there is maintenance care product

Refrigerator door was not closing "automatically", over time the plastic cams had worn out.

  • Customer: Mike from Egg Harbor Township NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.
All Instructions for the KSCS25FKSS02
886-900 of 1,189