Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSCS25FKSS02 > Instructions

KSCS25FKSS02 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25FKSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25FKSS02
871-885 of 1,189
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door wouldn't close fully, leaking cold air. light bulb went dead.

  • Customer: Mike from Sparks, NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the door (3 bolts on top). Removed the old plastic door closing cam on the bottom. Installed the new one. It was too tall (probably my fault), so I trimmed it with garden shears (it was a tubular piece of plastic). If you do this, be very careful, as the shears cut through the plastic MUCH easier than I thought. Popped the new one on, re-secured the door, and it works great now. Thank you partselect!

Bulb Replacement

  • Customer: Judith from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

water dispenser tube leaking at bottom

  • Customer: Ken from Hendersonville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TURN OFF WATER (if not already). Cut (or disconnect filler tube at bottom). Remove faceplate from refrigerator ice/water dispenser area. Remove screw holding metal bracket that holds water tube at filler point. Held metal mounting bracelet and pulled old filler tube out. Fed new filler tube thru bottom (hole is located at bottom of left door at hinge). As tube came out at top, pulled length needed to mount to new mounting bracket. Remounted new bracket (with hose attached) with new screw. Reconnected tube at bottom water line connection. Turn on water.

water dripping from spout

  • Customer: Terry from Union Star, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off water supply then Remove the dispencer trim by putting a flat screw driver into the slots at ths lower edge of trim and push down on trim as you pry the trim out and remove trim. Remove two screws holding the controls and unhook the far right connector and push to the side to get to old line,unhook the connecter at the bottom of door and remove compression nut from old line,remove the screw holding the old line in place and remove the assembly by pulling up and out. install new metal holder into slot and install screw to hold in place (If you have old style)cut new line at angle (Don't cut but about 1/2 inch off) and push new line down through hole at the bottom of the door where old one was and install the upper end into new metal bracket notch ,reinstall control panel with the two screws that were removed making sure that the controls strike the switches correctly ,reinstall the trim ,cut off the line to the match the connector and install the compression nut and put lines together,turn on water and check for leaks. Test and remove air and job should be complete. (hardest part was getting the trim off with out breaking it, I looked close and found the notches on the bottom)

would not make ice

  • Customer: Cynthia from Hinton, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video then made the repair it was just like the video said very easy

No Ice

  • Customer: Rodger from Fort Washington, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove icemaker control assembly, replaced with new one.

Ice maker stopped working

  • Customer: Elmo from Palm Coast, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
April 2012
My ice maker (2001 Whirlpool Gold side by side) stopped making ice. Using the model number (inside fridge, right wall), Google found the partselect website containing diagrams of the entire refrigerator. Using the "freezer liner" and "ice maker" diagrams, I discovered that electronic control boards, control and motor assembly, and water inlet valves could cause the ice maker to stop making ice. Since the LED lamps in the freezer liner were not working (diagnosis described as part of the emitter control board description), I replaced the emitter control boards first. After installation, the lights worked properly, according to the diagnosis, but still no ice. It seemed logical to next replace the control and motor assembly. About two hours after installation, the ice maker produced cubes, and has been working since. Each of the two parts orders from PartSupply came within 3 days, and were the correct parts for my machine. Installation illustrations were accurate and helpful

Ice maker not working

  • Customer: Gary from Plymouth, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the part recommended by your site, followed the instructions of the associated video and new ice is piling up right now. My only concern was no action for a time right after the install. Turns out the temperature of the freezer must drop back down to ?? before the ice maker starts to work. I was thinking maybe the electrical connection was not good. I choose to wait a night and see if change would occur. Freezer cooled down and ice maker started.

Gary

Unit stopped making Ice

  • Customer: Denis from Columbia, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found my unit had stopped making ice. I did 20 min. of search on the internet and found this site. I was going to just buy the whole ice maker unit, but after reading a bit more found that the majority was just the motor assembly. I ordered it, 2 days later it was at my front door. I pulled the ice maker unit out, took off the motor assembly, and low and behold a small whit ppiece of plastic fell out. I replaced the motor assembly re installed the ice maker and in one hour I had ice again. As far as ease to do this job from 1 being hard and 10 being super easy, I would rate this a 10+. If you have this kind of problem, I would not waste your money on a repair man, 150.00 service call, Hell no. 65 bucks and your done. Before your wife can make you a pot of coffee this can be out and back in. I don't want to take money away from the appliance repair men but some repairs can be a DIY project. Nut driver and phillips screw driver is all you need.Hope this helps ya.

timer motor died

  • Customer: Paul from Moline, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

ice maker wasn't

  • Customer: Mona from The Sea Ranch, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

No water coming into ice maker

  • Customer: Ricardo from Hialeah Gardens, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

Ice maker doesn't make ice.

  • Customer: Lowell from Discovery Bay, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Changed the Motor Assembly. Wasn't the problem. If I had followed your trouble chart a little farther I would have found out it was the circuit boards. All is well and I might add that yor guide with the parts and video are priceless. Very Happy. Lowell Onstad

stopped producing ice

  • Customer: Walter from Palm Beach Gardens, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

Ice Maker stopped working

  • Customer: Hector from San Diego, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Its the easiest repair in the world to do. Took less than 15 minutes. Removed the Icemaker unit from friedge, removed 3 screws replaced motor (very easy to do), 1 hr later I had Ice again! =)
All Instructions for the KSCS25FKSS02
871-885 of 1,189