Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSCS25FKSS02 > Instructions

KSCS25FKSS02 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25FKSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25FKSS02
856-870 of 1,189
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

freezer forming ice on back panel, fridge nor freezer getting cold

  • Customer: Frank from Alabaster, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

Part broke inside ice cube tray

  • Customer: Loren from Reeds Spring, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Using instructions found on the internet and the illustrated parts breakdown it was just a matter of following instructions.

Timer Was Hanging Up

  • Customer: WILLIAM from TERRE HAUTE, IN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off power,(breaker box), removed the ice container, this had the crusher, makes it easey to remove the timer assy, loosened up the upper hex head screws, removed the lower phillips screw. Dis-connect the feed wire assy. I elected to dis-connect first at the timer unit. Remove the timer cover, then access to the wire connecter,remove the heater unit on the side of the of water pan. Drop the unit out and if necessary change the wire loom at back of refrig-, install new loom if necessary, reverse process on ice unit. Took about 45 minutes +-, marked the timer dial, see if I got rotation, etc. There is ports on the face of the timer to check voltage's. Now will install new water valve , and water filter to make sure all is back to normal. Made ice on start up, excellent service, parts are great, with necessary information. Thanks, bill.

Plastic Ice Guide in door broke

  • Customer: James from Fair Oaks Ranch, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Align new Ice Guide with two upper tab holes and push into place. Then push bottom tab into bottom hole until it snaps into place.

qquit working a year ago

  • Customer: jeff from lawrenceburg, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Thought it would be difficult to replace and expensive. Very easy after all.

would not espense ice cube or crush them

  • Customer: Joe from Maryville, TN
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
ordered a new auger after tearing it apart I found I needed a drum. Thought this might be too much work so I went to Lowes for a new ice maker they sold me the wrong one said the didnt have one & I needed to order, they sent the wrong part. So I ordered the drum from you. So her is a pile of parts that has been settin there for a week. The secret was the video Great Job everything works & I tell everyone how smart I am with your help. THANKS

ice mold coating came off

  • Customer: Charles from Waco, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Told Wife To Watch The Instructional Movie, Got Me A Beer And Watched Football. She Finished In about Thirty Minutes.Good Job

Replace the Icemaker Motor Assembly

  • Customer: Michael from Meridian, ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The icemaker on oour Kenmore was fading fast. Ice was only being harvested once every 4-5 hours instead of every two. Then finally it stopped altogether. I did some research and decide that it was the motor assembly that needed to be replaced. I ordered the part and within 3 days it arrived. Within 45 minutes I replaced the part with the assistance of the youtube video. I am not a Mr. Fix-it but this was fairly straight forward. I am now a hero.

Door would not close on its own anymore

  • Customer: Richard from Midlothian, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
internet search

Door to the ice shute broken with worn out parts.

  • Customer: Edward from San Antonio, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took two screwdrivers and inserted bottom of bezel pryed up and out gently. Removed (4) screws and unpluged (3) electronic plugs removing the circuit board. After you remove bezel & circuit board you have a chance to see what you are doing and get to the problem area with more ease. Remove old parts and reverse it putting the new parts. Process is very simple just pay attention to the order everything was removed. On my frig one of the plastic ears that hold the pin which holds the spring and door was broke. The piece I needed was no longer avaliable. I had to use a piece of the plastic from the old parts I removed, drilled a hole the size of the pin in it and glued it to the broken off ear. Put everything back together and I am pleased to say that everything works fine! So you might need to go a little MacGyver on it. All in all very simple fix.

Auger drum broke

  • Customer: Ed from Thurmont, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Removed ice bin and separated parts. However, instructions would have been nice that the part to unscrew was the opposite of normal screws. Not righty-tighty, but righty remove. After I figured that out, disassembly, reassembly, and installation went smoothly. It was a pleasure to deal with your company!

Ice door hinge was broke and not letting door close building up ice between door and ice maker.

  • Customer: billy from cleveland, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Popped the cover off took panal off to access ice door screws.Removed old parts and replaced with new kit.Works fine now.

Loud knocking noise when opening door

  • Customer: William from Land O Lakes, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.

Refrigerator door would not self close

  • Customer: Robert from Palo Alto, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed food from door. Shut off fridge. Removed dust cap at top hinge. Marked location of top hinge with masking tape so lining up when reassembling would be easier. Removed screws holding top hinge to fridge. Removed door, placed on blanket&towel. Removed old door cam. Put on new door cam. Removed old hinge cam. Put on new hinge cam. Put door back on. Replaced top hinge, lining up with tape. Replaced dust cap. Note that door did not really self close very well until it was filled with food. By far the hardest part of the whole operation was that my wife wanted to clean the fridge in the process!

stopped making ice

  • Customer: Richard from DeBary, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed flap and three screws holding tray. one screw holding plug protector. Slid tray out and unplugged . Removed three screws holding control & motor assembly.Put new unit in reassembled.
All Instructions for the KSCS25FKSS02
856-870 of 1,189