Models > KRFF15KSWHY0 > Instructions

KRFF15KSWHY0 KitchenAid Freezer - Instructions

All installation instructions for KRFF15KSWHY0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KRFF15KSWHY0
151-163 of 163
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

NO LIGHT

  • Customer: Mary from Jefferson Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK SOCKET OUT AND REPLACE IT WITH NEW ONE. VERY EASY. W SAVED ALOT OF MONEY DOING IT OURSELF.

Frig not cooling.

  • Customer: Adam from Randolph ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

replace hinge bracket on fridge door

  • Customer: Albert from Dunmore PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

The refrigerator was running but blowing hot air, everything in freezer had defrosted.

  • Customer: Jeanne from Fairview Heights IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.

refridgerator was not cooling to the proper temps and finally would not cool at all

  • Customer: John from LAS CRUCES NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.

Broken roller wheels

  • Customer: Joseph from Tyrone PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

Evap Fan Motor went bad

  • Customer: Aaron from Metz WV
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This was an easy part to find thanks to its universality. The only difficulty was the electric snap-on connection - had to use the old one and tie the wires to the new motor - that was easy. Hardest part was the new screws to mount to bracket weren't long enough. Had to find one in my screw jar to match threads that was long enough. Works Great!!!

Fan motor worn out

  • Customer: Myrna from Decatur IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My Son who is not an appliance repairman did it for me. He had some difficulty getting the nuts and bolts loose mainly. Sorry I'm not much help other than that! I would like to compliment you on your fast service, first time ordering from you and it was for an older model refrigerator that my repairman said he couldn't find. It's working fine now and I'm a satisfied customer!

condenser motor broke

  • Customer: patrick from livonia MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.

wouldn't make ice, door seal was hot to touch, warm in fridge.

  • Customer: Dale from Sterling AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
I folded in half twice! and took the back off the fridge(cardboard) and took one brace off and just took the screws off the fan from the other two braces. Turned the fan enough to get at the wires for the fan and cut them off an inch from the old fan, stripped the insulation and wire nutted them to new fan. Make sure they don't interfere with the new fan and put the new fan in place put the screws in and we're making ice and cold fridge again.

One front and one rear fell apart upon moving refridgerator.

  • Customer: paul from colchester CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

intermittent loud whirring noise

  • Customer: Honz from Tucson AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Moved fridge out from wall, unplugged power cord. Laid on floor, removed 6 screws from cover. Removed one threaded bolt to allow assembly to slide out. Removed special nut, and took fan off. Removed 3 motor mounting bolts. Unscrewed 2 wire nuts, and untwisted wires. (option 1, no ground) Vacuumed entire area around motor. Used 3 bolts to mount motor to holder assembly, and special nut to install fan. Stripped wires back about 3/4 inch. Twisted two wires together CW, and installed new wire nuts. Slid motor assembly back into slot,(keep wires away from blades) and used one threaded bolt to secure assembly. Reinstalled cover plate with 6 screws. Plugged power cord in to test air flow (out through cover vents). Moved fridge back into place. The loud whirring noise did not stop for a day; then quiet!

Water was running into refrig from freezer and ice cream was soft

  • Customer: William from Delano MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH
All Instructions for the KRFF15KSWHY0
151-163 of 163