KPDJ630Y0 KitchenAid Dishwasher - Instructions

I am a 73 year old lady. My nephew found the torn rubber water delivery tube after a repairman had found nothing. I looked up the model number, contacted Part Select by e-mail, ordered the part ($15.++ for cost and delivery), read reviews and found tipe for installation. Total time spent on installation was less than ten minutes. The round tube, with a smidgen of liquid detergent inside each end of the tube, fits onto the water line; the other end of the tube will squeeze flat with little effort, and fits onto the apray arm.

I bought the kit because it had other parts that I thought I needed.

I unscrewed the screws and slid the panels in. Very easy. I wanted all the appliances to have a stainless steel look.

I ordered 8 new axles and used old wheels. I broke off the remaining axle parts left on the wire lower basket with just my hands, and then popped on the new axles. This was done without tools; just needed significant pressure to pop the axles onto the coated wire. The wheels popped onto the axles with a little pressure. Make sure you have the right side of the wheel out. I simply looked at the remaining working wheels before install began to make sure which side goes out. Very easy install.

Used screwdriver to pry off other end of water tube. Kind of cooked on over the years and rear connection point is on a part that is not real strong so you have to be careful to not break or bend the connection. New tube is very tight to get on so putting it on required using the blade of the screwdriver to get the tube to streatch over the two connection points, but not real difficult. Now it's good as new!

First removed old hose from the upper rack. Used hair dryer to heat the hose up ( hose was a little stiff) and installed hose. It's pretty simple to install, I didn't even have to unload the dishwasher

The whole operation took about 5 minutes which included opening the package! Sprayed some vegetable spray inside the opening of the water tube that attached to the spray connection and it slipped right on. Absolutely amazing and I feel like I have a brand new dishwater! My dishes are definitely cleaner too! Thank you Parts Select for posting how to instructions!

I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.

i pulled the rack out, took off the old parts then added the new ones. it was quick and simple. i needed no tools and my package of parts arrived quicker than i thought. thanks!

I removed the old tube by hand (it fell apart) I just worrked the new softer tube over the openings on each end and it was fixed! I did have to warm the new tube with warm water to squeeze it over the tubes but it was easy!

It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!

Part was easy to locate on the website. Photo on the measurement grid was the key after entering the maker and model number. I have found refrigerator parts the same way on this site. Sliced the old rotten hose to remove it. The new hose only had to be slipped over the connections. I soaped the ends of the tube to make the installation easier.

I just slipped the old, worn out tube off, warmed the new one in some hot water for a few minutes to make it more pliable, sprayed some non-stick spray on the end connecting in the back, and slipped it on. Piece of cake!

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.