Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Touch pad on dishwasher dead
1. Remove the two screws that attach the bottom cover. 2. Remove the 2 screws that attach the door outer cover. 3. Remove the 8 screws that attache the door inner cover. 4. Remove the plastic cover over the electronic controller. 5. Remove the two connections to the thermal fuse. 6. Remove the thermal fuse. 7. Install the new thermal fuse. Reverse the above steps.
Unplug the dishwasher. Simply removed 8 screws on the inside of the door, removed the interior door panel. Next popped of the plastic protective electrical panel cover. Locate the Thermal fuse that had simple instructions provided. Removed the fuse and replaced the harness. Put everything back together. Plugged dishwasher back into electrical outlet...Dishwasher resumed with the cycle that the dishwasher was in when the fuse blew. Simple, Fast AND Reliable!!!
The machine just quit in the middle of a cycle and there were no lights on the control panel
There were eight of the star head screws to remove to take the front off the dishwasher, then just followed the instructions that came with the part, which was a thermal fuse and the new wiring that accompanied the fuse in the order. The hardest part was getting the old wire out of the harness with the other three, but once I figured that out just slid the new wire into place and made the connections. I reinserted the screws, turned the power on and knock on wood shes still working.
Stopped Running,Will Not Start, and Clean LED Blinks 7 times then repeats
Got Maintenance Flyer out an read about problem Removed access plate Disconnectd water and drain Removed anchor screws Pulled unit out and disconnedted from Electric Flipped on it's back Ohmed out all heat related items and found discrepency with Thermisitor resistance Ordered and received Part Changed out Thermisitor Checked wiring to Heater and replaced connections Hooked electric up Ran Diognostics per Maintenance flyer and cleared fault Hooked back up and ran like a champ
The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem
it would turn off and on mid-cycle and finally quit completely
I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!
Dishwasher's "clean" light just blinked - wouldn't run. Repairman came and found out problem and suggested I could fix it myself
Since I had watched a repairman diagnose the problem, it was eash to reproduce how to pull the unit out from the wall and find the faulty part to remove it and replace it with the new thermistor. Two wires to disconnect and connect and repair nearly complete. Pushed it back in, screwed it back to the cabinet and installed foot plate and done.
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Stopping in the middle of cycle. Finally quit completely.
Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.