Models > KHWV01RSS0

KHWV01RSS0 KitchenAid Washer - Overview

Get Parts and Repair Help for KHWV01RSS0

If you know the washer repair part you need, you can browse the list of all parts on the KHWV01RSS0, or you can search by name or part description. You can also find your part by where it is located on the KHWV01RSS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$82.92

Bellow

This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub. Clamps are not included. Must order clamps separately, if needed.

$26.88

Drum Baffle

Sold individually. This part moves the clothes around inside your dryer/washer and helps to direct the flow of hot air during the drying cycle.

$36.88

Shock Absorber

Shock absorbers help keep the washer from vigorous shaking during its cycles. Note: They are sold individually. Order quantity needed.

$47.68

Water Inlet Valve

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

$14.70

Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.

$43.61

Flowmeter

This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.

$14.54

Bellow Clamp

This is used to help hold the bellow in place.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$38.98

Detergent Dispenser Drawer

$10.94

Drain Hose

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellows were moldy, needed to replace

  • Customer: Franck from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 206 of 221 people found this instruction helpful
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached... read more

My washer would not always finsh the cycle (most of the time it would run between 2 and 30 minutes) and then the time display would flash and the washer would shut down and beep. An f06 fault code flashed in the display.

  • Customer: Bradley from Red Wing MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 63 of 71 people found this instruction helpful
First I removed the screws and the plastic slide clips to remove the back plate. I then went to the lower right of the washer and found the motor control unit. It has about four plus going into it. The front inside mount of the control unit has a clip on it that must be pushed so you can pull the unit free of the bottom of the machine. Once the control u... read more

Washer made loud banging noise during spin cycle

  • Customer: Francis from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 50 of 60 people found this instruction helpful
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in s... read more