KHWS01PWH0 KitchenAid Washer - Instructions

My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you

The product came on time and was perfectly rapped , it took me 15 mins to install after watching you tube videos on front loader washer . I was happy I didn't have to call a service man in . . . .

pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.

Very easy repair, once I read the reviews and watched a couple of you tube videos. I just released the band holding the gasket in place, pulled it back, unscrewed the latch and installed a new one. Less than a 10 min job. I am glad I found this web site, thanks guys!!

I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!

Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.

We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation

Easily took the old door off of the dryer unit then removed the hinge bracket and replaced it with the new part.

Used nut driver to remove 3 screws from rear of washer and remove washer top. Used Torx driver to remove single screw holding valve assembly in place. Loosened hose clamp with adjustable pliers and then unplugged 6 electrical plugs. Reversed process to put everything back together. Very simple.

1. Unplugged washer. 2. Turned off water supply valves. 3. Disconnected water supply hoses from back of washer. 4. Removed three (3) screws that secure top of washer from top/back of washer. 5. Removed top of washer. 6. Disconnected water outlet line from old inlet valve assembly by releasing clamp. 7. Labeled and disconnected spade connections from old inlet valve. 8. Removed single (1) screw securing old inlet valve in place and removed valve from washer. 9. Re-assembled using new inlet valve lickety split faster than a five-legged skunk.

I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

Removed top of washer and replaced flow meter.

Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

repair was a cake-walk with the video there to help.Thanx