Models > KHWS01PMT3 > Instructions

KHWS01PMT3 KitchenAid Washer - Instructions

All installation instructions for KHWS01PMT3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KHWS01PMT3
61-75 of 182
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The water didn't drain, so the drum wouldn't spin

  • Customer: Jill from New Rochelle NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

Shaft in water pump broke

  • Customer: Jeffrey from Adrian MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 4 of 4 people found this instruction helpful
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

Door hinge had rusted out and was not closing properly

  • Customer: Sylvia from El Paso TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 5 of 7 people found this instruction helpful
We had to bread the hinge that had rusted out. That was the worst part. Putting the new hinge was no big deal. The time factor was also great. I called on Monday and had the part by Thursay. With a family of 6 a washer is a huge necessity.

washer filled with water overnight

  • Customer: ROBERT from Millville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
following the procedure was easy except the alignment of the new valve was off by 1/4 inch and I had to drill an additional hole to reuse the screw for attachment. Piece of cake otherwise.

Constant washer Faulting with a FH fault code

  • Customer: Bruce from Salisbury MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 4 of 5 people found this instruction helpful
This washer had been faulting since it was 1 year old but it only happened 1 to 2 times a year. As the fault problem became more often, I realized it was a hardware or computer malfunction. But what was the problem? Well the problem always was a faulty flow meter. I replace the valve and the flow meter. But I tested the flow meter several times.-- I replaced the flow meter and the valve. And for once in 5 years it did not fault.

Baffle was worn out/broken

  • Customer: Day from Basking Ridge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!

FOLLOWING THE INSTRUCTIONS OF THE REPAIR MANUEL,

  • Customer: gerard from arvada CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
FIRST I REMOVED THE RETAINER RING AND THEN PULLED BACK ENOUGH OF THE BOOT TO GET THE DOOR SWITCH OUT AND PLUGGED IN THE NEW SWITCH PUT THE RETAINER RING BACK ON AND IT WAS FINISHED. WITH OUT THE REPAIR BOOK I WOULD HAVE BEEN LOST ON HOW TO DO THE JOB.

Front seal leaked

  • Customer: Ramon from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 11 people found this instruction helpful
It was so easy my wife replaced the part.

F-20 ERROR CODE

  • Customer: GARY from CLARKSVILLE IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 6 people found this instruction helpful
TAKE OFF TOP OF WASHER AND THE FLOWMETER IS IN THE BACK LEFTHAND CORNER ON THE TOP OF THE WASHER.REPLACED THE WATER LEVEL SWITCH ON THE TOP RIGHTHAND OF THE MACHINE ALSO. GOT ABOUT 150.00 TOTAL INVESTED W/SERVICE CALL FROM LOCAL TECH.F-20 HAS NOT CAME BACK YET. I HOPED IT FIXED IT WASHER IS ONLY 3 YRS. OLD. -GD

Pump not working

  • Customer: Darrell from Lady Lake FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Replaced pump

baffle connectors worn off

  • Customer: richard from chetek WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Placed baffle inside of washer and pulled to lock into place. EASY!!!

The washer was unable to run without door locking

  • Customer: MICHAEL from DERIDDER LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .

door would not latch , and lights on front just flashed

  • Customer: FRANCIS from leesburg FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

Pump not draining the water out.

  • Customer: Martin from Kotzebue AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.

Washer wouldn't drain

  • Customer: Jeff from Barrington RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Easily. 4 Screws. 2 Clamps.
All Instructions for the KHWS01PMT3
61-75 of 182