Models > KHMS2050SSS0 > Instructions

KHMS2050SSS0 KitchenAid Microwave - Instructions

All installation instructions for KHMS2050SSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KHMS2050SSS0
1-15 of 22
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Glass cooking tray broke

  • Customer: Mark from Agua Dulce CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 21 people found this instruction helpful
There was no "fixing" per say but we still could not use the microwave without the plate. This has to be one of the biggest plates for a microwave. We ordered this through your company and we had it three days later. THREE DAYS! We had expected anywhere from 1-2 weeks. My husband was so impressed he bookmarked your site for future reference. Thank you for being so efficient and prompt. The glass turntable fit like a glove! Sincerely, Mark and Lia Hammond

Fire in microwave melted several parts

  • Customer: duane from san diego CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 16 of 30 people found this instruction helpful
Remove the filters and use a Torx driver to remove two screws holding the motor. The wires on on the motor are held in place by a plastic clamp that must be pried open on one side. That's all it takes to replace the drive motor. Everything else that makes the turntable spin lifts off from inside the microwave.

Lost spring that holds filter in hood that was lost when cleaning it.

  • Customer: Raymond from Mechanicsville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
simply removed the filter casing from the microwave, then removed both filters and inserted the spring after bending it slightly.

The door of my whirlpool microwave broke off

  • Customer: Pete from Kensington MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 10 people found this instruction helpful
I purchased the door handle to model KHMS1850SWH0 for around $50; the model I have,KHMS1850SWH1, only offers the entire door as a replacement for over $200. The earlier model door handle fit great with no problems.

light bulbs nedd to repace it.

  • Customer: Jorge from Bay Point CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 103 people found this instruction helpful
Took the the want burned out , and put the new ones.

LIGHT BURNED OUT

  • Customer: Patti from Coarsegold CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
FOLLOWED THE INSTRUCTION BOOKLET THAT CAME WITH THE MICROWAVE. VERY EASY.

it was working fine and it stopped order a fuse and it wasn't the problem

  • Customer: Herb from Auburn IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse

Dirty filters

  • Customer: Anna from Antioch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the dirty ones and put in the new ones. This was really not a repair. No tools needed.

door handle broke

  • Customer: doyle from woodland WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
followed on-line instructions and it was very easy to do. just seperated the inter-door from the outer-door and exposed the 2 screws. lined up the door handle with the scr and screwed the handle on. snapped the doors back together and it was done.

need new filter

  • Customer: donald from payson AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced old filter

Bulb Finally went out

  • Customer: Jeff from Hanahan SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used an apex bit unscrewed the fittingand down came the light cover. Pulled the old bulb out and had to use a flashlight to line the prongs up to install the new one. Whileeverything was down used an oven cleaner to degrease and clean EVERYTHING. You wouldn't beleive how much grease and debris will accumulate in 5 years. And I only fry bacon once in a blue moon. All in all it was simple to order, clean, and repair.

Light burned

  • Customer: Jennifer from Red Oak IA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed the lens cover anbd inserted the new bulb. Put the cover back on and there was light!

burned out overhead light

  • Customer: Sharon from Anoka MN
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Some difficulty getting screw loosened, once that was done replaced burned out bulb.

machine was dead.

  • Customer: Mark from Smithtown NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Replace charcoal filter

  • Customer: Louise from Mason OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took old one out,and clipped new one in.
All Instructions for the KHMS2050SSS0
1-15 of 22