Models > KHMS155LSS4 > Instructions

KHMS155LSS4 KitchenAid Microwave - Instructions

All installation instructions for KHMS155LSS4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KHMS155LSS4
61-75 of 87
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

left something in microwave too long and burned parts

  • Customer: Norman from Angier NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced burnt parts

Microwave turns on but did not heat

  • Customer: John from Port Saint Lucie FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.

Light burned

  • Customer: Jennifer from Red Oak IA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed the lens cover anbd inserted the new bulb. Put the cover back on and there was light!

burned out overhead light

  • Customer: Sharon from Anoka MN
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Some difficulty getting screw loosened, once that was done replaced burned out bulb.

replace door handle

  • Customer: Hugh from Potomac Falls VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
had to go on the internet to find out how to take front door apart..

replacement of filters

  • Customer: THEODOROS from VIRGINIA BEACH VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just replaced the filters

Replace door handle

  • Customer: Carl from Woodridge IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Taking the door apart was easy once you figured out how it came apart. Youtube videos were not helpful as every brand of microwave is different; what works for one does not work for another. My Kitchenaide has little interior hooks on the inside of the door, 8 on top, 8 on bottom, 4 on the hinge side. You have to pry the door-skin up to get teh hook disengaged, then get a putty knife or similar to keep the hooks from re-engaging. Once you have about 6 or 7 undone, the door starts to come apart. Eventually the exterior of the door comes off; the interior of the door remains hinged. After that, you'll figure it out...

Microwave would not heat

  • Customer: Gary from Chesapeake VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed microwave case and bad part was right there in plain sight attached to the magatron. Two screws and two wires and part replacement was done. Plugged in microwave and works perfect. Couldn't have been any easier. Thanks for the easy troubleshooting and parts suggestions on your site.

machine was dead.

  • Customer: Mark from Smithtown NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Plastic Door handle broke off

  • Customer: thomas from orlando FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the 3 screws in the door. You will have to pry the door frame apart. use 1 or more flat screwdrivers to pry the inner liner from the medal door. There are plastic pieces that recess into the inner door from the medal frame. Once you get a few loose it is easy to remove the frame. Locate the 2 screws from the handle and attach the new handle. Then reverse the process to put the frame and inner door back together and put the 3 screws back in.

rotating glass dish assembly making stange noise

  • Customer: Lawrence from Excelsior MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The lady in the Nova Scotia call center should get all the credit for being able to identify the part I needed from only the very limited information I was able to give her. Employee of the month for her. She also had such a great can do attitude. Lawence Baier

Broke a 15 year old glass cooking tray

  • Customer: Stephanie from La Jolla CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered the item on a Monday at 12pm and it arrived the next day. Amazing!

glass cooking tray droped and broken

  • Customer: janice from dunn NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just replace need cooking tray

surface light on microwave wasnt' working

  • Customer: Dotty from Hillsboro WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the light assembly off and replaced the bulb and put the assembly together and fitted back in the space and finished the assembly.

Broken turntable support ring and missing support

  • Customer: Sharon from Pleasanton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched video which reminded me to order support for the turntable support ring and did exactly what the person in the video did. Excellent and prompt service and all parts fit.
All Instructions for the KHMS155LSS4
61-75 of 87