Models > KHMS155LSS0 > Instructions

KHMS155LSS0 KitchenAid Microwave - Instructions

All installation instructions for KHMS155LSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KHMS155LSS0
151-159 of 159
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

5 year old daughter broke the handle and door panel

  • Customer: Eric from North Little Rock AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the three screws on the side popped the whole panel off, unscrewed the handle and used those screws for the new handle. Removed and transferred the glass panel held down with hot glue. Popped the new panel back on the door and screwed the three screws back in to hold. Took about twenty minutes.

Broken handle

  • Customer: Fernando from Wellington FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The hard part was to unusable the back door.It took me a while but I was able to do it. The res it was easier just put the new handle in place and secure it with a screw driver.

outer door skin of microwave was cracked and breaking off.

  • Customer: Larry from Wellington FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old outer door skin carefully so as not to break inner door or attached glass. 3 screws removed for new door skin and 2 screws need to be removed for the door handle that was not broke. Use same screws and replace on new door skin. Most of the new door skin snaps into place and is secured with the old screws. Easy maybe 15 min. to complete. Needed to pry old door skin off with flat head screw driver carefully.

vent plastic broken kept vent falling down on stove

  • Customer: Jesse from VICTORVILLE CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
remove old vent that was held in place by clips and two screws re-installed. Only problem is that should have ordered new clips was not aware that they did not come with the new vent

needed to replace door handle

  • Customer: patrick from ruidoso NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Open door remove the 3 screws Gently prior door apart. the outer metal piece with glass comes off easily, unscreew door handle. alignn new3 handle an use the same screew ro attach door handle. Replace outer metal piece the replace 3 screws One tool needed a phillips head

broken glass cooking tray for microwave

  • Customer: Vanessa from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Twas really easy considering that all I had to do was place the plate back in the microwave. Easy Peasey

broken glass microwave tray

  • Customer: Ronald from Rhinelander WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Tray arrived in a short period of time and was a perfect match.

Replace turntable motor

  • Customer: Monty from Mansfield TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

Microwave Vent Hood Filters

  • Customer: Vicki from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Not so sure this would qualify as "instructions", but I only needed a screwdriver because the "D" rings of the old vent filters broke off and I had to pry to old ones out. Keep in mind, I am mechanically disadvantaged and can barely change an A/C filter ... that being said, all I did for this order was input my Model number and PartSelect found the correct replacement part. I receive the parts super quick (faster than the other 2 purchases I did that day). The only bummer was the packaging ... super huge box for small tiny parts. Otherwise, I now know where to go for replacement parts. This project should be a "no-brainer" for most DYI's, so getting the right parts with just a model number was lifesaving for me :0)
All Instructions for the KHMS155LSS0
151-159 of 159